581020
6
Zoom out
Zoom in
Previous page
1/12
Next page
6
Warning! The vibration emission value during actual use of
the power tool can differ from the declared value depending
on the ways in which the tool is used. The vibration level may
increase above the level stated.
When assessing vibration exposure to determine safety
measures required by 2002/44/EC to protect persons regularly
using power tools in employment, an estimation of vibration
exposure should consider, the actual conditions of use and the
way the tool is used, including taking account of all parts of
the operating cycle such as the times when the tool is
switched off and when it is running idle in addition to the
trigger time.
Labels on tool
The following pictograms are shown on the tool:
:
Warning! To reduce the risk of injury, the user must
read the instruction manual.
Electrical safety
#
This tool is double insulated; therefore no earth wire
is required. Always check that the power supply
corresponds to the voltage on the rating plate.
u If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised Black & Decker Service
Centre in order to avoid a hazard.
Features
This tool includes some or all of the following features.
1. Variable speed switch
2. Lock-on button
3. Saw blade locking lever
4. Saw blade support roller
5. Saw blade
6. Shoe plate
7. Shoe plate locking knob
8. Saw blade storage compartment
9. Dust extraction adaptor
Assembly
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
Fitting the saw blade (g. A)
u Hold the saw blade (5) as shown, with the teeth facing
forward.
u Push the lever (3) downwards.
u Insert the shank of the saw blade into the blade holder (10)
as far as it will go.
u Release the lever.
u Adjust the blade support roller as described below.
Adjusting the blade support roller (g. B)
After tting the blade, you need to adjust the blade support
roller (4).
u Turn the locking knob (7) in direction A.
u Slide the blade support roller against the rear of the blade.
The blade must locate in the central recess of the roller.
u Turn the locking knob (7) in direction B to lock the shoe
plate in place.
Connecting a vacuum cleaner to the tool (g. C & D)
u Align the dust extraction adaptor (9) with the saw shoe as
shown.
u Insert the ribs (12) into the slots (13).
u Rotate the adaptor until it locks into position. Make sure
that the ribs (14) are correctly seated.
u Connect the vacuum cleaner hose (11) (not supplied) to
the adaptor.
Dust extraction is not possible when making bevel cuts.
Use
Warning! Let the tool work at its own pace. Do not overload.
Warning! Never use the tool when the saw shoe is loose or
removed.
Adjusting the shoe plate for bevel cuts (g. E)
The shoe plate can be set to a left or right bevel angle of up to
45°.
u Turn the locking knob (7) in direction A to release the shoe
plate (6).
u Pull the shoe plate (6) backwards and set it to the required
angle. You can use the scale or a protractor to check the
angle.
u Turn the locking knob (7) in direction B to lock the shoe
plate in place.
To reset the shoe plate for straight cuts:
u Turn the locking knob (7) in direction A to release the shoe
plate (6).
u Pull the shoe plate backwards and set it to an angle of
approx. 0°.
u Push the shoe plate forward.
u Turn the locking knob (7) in direction B to lock the shoe
plate in place. Make sure that the shoe plate is supported
by the guide ribs.
Switching on and off
u To switch the tool on, press the variable speed switch (1).
The tool speed depends on how far you press the switch.
u For continuous operation, press the lock-on button (2) and
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker KS888E T1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker KS888E T1 in the language / languages: English as an attachment in your email.

The manual is 0,68 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Black Decker KS888E T1

Black Decker KS888E T1 User Manual - English, German, Dutch, Danish, French, Italian, Portuguese, Swedish - 76 pages

Black Decker KS888E T1 User Manual - Turkish - 8 pages

Black Decker KS888E T1 User Manual - Spanish, Spanish, Norwegian, Finnish - 76 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info