580991

Black Decker KS777 T1 Manual

6
Zoom out
Zoom in
Previous page
1/76
Next page
6
ENGLISH
Labels on tools
Electrical safety
This tool is double insulated; therefore no earth
wire is required. Always check that the power
supply corresponds to the voltage on the rating
plate.
This appliance is not intended for use by young or infirm
persons without supervision. Children must be
supervised to ensure they do not play with the
appliance.
If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised Black & Decker Service
Centre in order to avoid a hazard.
Features
1. Lock-on button
2. Variable speed on/off switch
3. Blade storage compartment cover
4. Shoe plate
5. Blade support roller
6. Tool-free blade clamp
Assembly
Warning! Before attempting any of the following
operations, make sure that the tool is switched off and
unplugged and that the saw blade has stopped. Used saw
blades may be hot.
Fitting the saw blade (fig. A)
Hold the saw blade (7) as shown, with the teeth facing
forward.
Push and hold the blade clamp (6) down.
Insert the shank of the saw blade into the blade holder
(8) as far as it will go.
Release the blade clamp (6).
Saw blade storage (fig. B)
Saw blades (7) can be stored in the storage compartment
located on the side of the tool.
Open the cover (3) of the saw blade storage
compartment by holding the tab on the top of the cover
(3) and pulling it outward.
The blades are retained in the compartment by a
magnetic strip. To remove a blade, press down on one
end of the blade to raise the other end, and remove.
Close the cover (3) of the saw blade storage
compartment and make sure that it is latched closed.
Warning! Close the compartment door securely before
operating the saw.
Residual risks
Additional residual risks may arise when using the tool which
may not be included in the enclosed safety warnings. These
risks can arise from misuse, prolonged use etc.
Even with the application of the relevant safety regulations
and the implementation of safety devices, certain residual
risks cannot be avoided. These include:
Injuries caused by touching any rotating/moving parts.
Injuries caused when changing any parts, blades or
accessories.
Injuries caused by prolonged use of a tool. When using
any tool for prolonged periods make sure you take
regular breaks.
Impairment of hearing.
Health hazards caused by breathing dust developed
when using your tool (example:- working with wood,
especially oak, beech and MDF).
Use
Adjusting the shoe plate for bevel cuts (fig. C)
The shoe plate (4) can be set to make either a straight cut or
a left or right bevel cut at an angle of 45°.
Loosen the screws (9).
Pull the shoe plate (4) forward, rotate the shoe plate (4) to
the left or right and push it back into the 45° location.
Tighten the screws (9).
To reset the shoe plate for straight cuts:
Loosen the screws (9).
Pull the shoe plate (4) forward, rotate to the centre and
push it back into the 0° location.
Tighten the screws (9).
Variable speed control
The tool has a variable speed on/off switch (1). The
operating speed depends on how far you press the switch.
Use a high speed for wood, medium speed for aluminium
and PVC and low speed for metals other than aluminium.
Switching on and off
To switch the tool on, press the variable speed on/off
switch (2).
To switch the tool off, release the variable speed on/off
switch (2).
For continuous operation, press the lock-on button (1)
and release the on/off switch (2).
To switch the tool off when in continuous operation,
press the on/off switch (2) and release it.
Warning! To reduce the risk of injury, the user
must read the instruction manual.
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker KS777 T1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker KS777 T1 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,95 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Black Decker KS777 T1

Black Decker KS777 T1 Quick start guide - English - 12 pages

Black Decker KS777 T1 User Manual - Polish, Turkish - 72 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info