Manual Black Decker KS702PE T1 (page 5 of 76) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Spanish, Norwegian, Finnish)

580977

Zoom out

Zoom in

1/76

ENGLISH

f. Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are less

likely to bind and are easier to control.

g. Use the power tool, accessories and tool bits etc.,

in accordance with these instructions, taking into

account the working conditions and the work to be

performed. Use of the power tool for operations different

from those intended could result in a hazardous situation.

5. Service

a. Haveyourpowertoolservicedbyaqualiedrepair

person using only identical replacement parts. This will

ensure that the safety of the power tool is maintained.

Additional power tool safety warnings

Warning! Additional safety warnings for jigsaws and

reciprocating saws

u Hold the tool by the insulated gripping surfaces when

performing an operation where the cutting tool may

contact hidden wiring or its own cord. Cutting

accessory contacting a "live" wire may make exposed

metal parts of the power tool "live" and shock the operator.

u Use clamps or another practical way to secure and

support the workpiece to a stable platform. Holding the

work by hand or against your body leaves it unstable and

may lead to loss of control.

u Keep hands away from cutting area. Never reach

underneath the work piece for any reason. Do not insert

ngers or thumb into the vicinity of the reciprocating blade

and blade clamp. Do not stabilize the saw by gripping the

shoe.

u Keep blades sharp. Dull or damaged blades may cause

the saw to swerve or stall under pressure. Always use the

appropriate type of saw blade for the workpiece material

and type of cut.

u When cutting pipe or conduit, make sure that they are free

from water, electrical wiring, etc.

u Do not touch the workpiece or the blade immediately after

operating the tool. They can become very hot.

u Be aware of hidden hazards, before cutting into walls, oors

or ceilings, check for the location of wiring and pipes.

u The blade will continue to move after releasing the switch.

Always switch the tool off and wait for the saw blade to

come to a complete standstill before putting the tool down.

Warning! Contact with, or inhalation of dusts arising from

cutting applications may endanger the health of the operator

and possible bystanders. Wear a dust mask specically

designed for protection against dust and fumes and ensure

that persons within or entering the work area are also

protected.

u This tool is not intended for use by persons (including

children) with reduced physical, sensory or mental

capabilities, or lack of experience and knowledge, unless

they have been given supervision or instruction

concerning use of the appliance by a person responsible

for their safety. Children should be supervised to ensure

that they do not play with the appliance.

u The intended use is described in this instruction manual.

The use of any accessory or attachment or performance

of any operation with this tool other than those

recommended in this instruction manual may present

a risk of personal injury and/or damage to property.

Vibration

The declared vibration emission values stated in the technical

data and the declaration of conformity have been measured in

accordance with a standard test method provided by

EN 60745 and may be used for comparing one tool with

another. The declared vibration emission value may also be

used in a preliminary assessment of exposure.

Warning! The vibration emission value during actual use of

the power tool can differ from the declared value depending

on the ways in which the tool is used. The vibration level may

increase above the level stated.

When assessing vibration exposure to determine safety

measures required by 2002/44/EC to protect persons regularly

using power tools in employment, an estimation of vibration

exposure should consider, the actual conditions of use and the

way the tool is used, including taking account of all parts of the

operating cycle such as the times when the tool is switched off

and when it is running idle in addition to the trigger time.

Labels on tool

The following pictograms are shown on the tool:

Warning! To reduce the risk of injury, the user must

read the instruction manual.

Electrical safety

This tool is double insulated; therefore no earth wire

is required. Always check that the power supply

corresponds to the voltage on the rating plate.

u If the supply cord is damaged, it must be replaced by the

manufacturer or an authorised Black & Decker Service

Centre in order to avoid a hazard.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker KS702PE T1 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,27 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Black Decker KS702PE T1 Manual

Product: