580886
8
Zoom out
Zoom in
Previous page
1/76
Next page
8
ENGLISH
Insert the shank of the saw blade (7) into the
blade holder (9) as far as it will go.
Slightly tighten the two screws (10) alternately
to position the blade, then fully tighten the two
screws (10).
Adjust the saw blade support roller (5) as
described above.
To remove the saw blade (7), turn both screws
(10) one turn counter-clockwise.
Connecting a vacuum cleaner to the tool
(fi g. D)
An adaptor (11) is required to connect a vacuum
cleaner or dust extractor to the tool. The adaptor
can be purchased from your local Black & Decker
retailer.
Push the adaptor (11) into the dust extraction
outlet (3).
Connect the vacuum cleaner hose (12) to the
adaptor (11).
Saw blade storage (KS602E & KS603E only)
(fi g. E)
Saw blades (7) can be stored in the storage
compartment (6) located on the side of the tool
Open the cover of the saw blade storage
compartment (6) by holding the tab on the top
of the door and pulling outwards.
Remove or store saw blades (7) in the storage
compartment (6).
Close the cover of the saw blade storage
compartment (6) and make sure that it is
latched closed.
Cut line blower (fi g. F)
To aid visibility when cutting, your jigsaw is
equipped with a cut line blower (13) which will
keep the work area clear of dust as you saw.
Use
Adjusting the shoe plate for bevel cuts (fi g.
G)
The shoe plate can be set to make either a straight
cut or a left or right bevel cut at an angle of 45°.
Loosen the screws (8).
Pull the shoe plate (4) forward, rotate the shoe
plate (4) to the left or right and push it back into
the 45° location.
Push the blade support roller (5) forward until it
touches the saw blade (7).
Tighten the screws (8).
To reset the shoe plate for straight cuts:
Loosen the screws (8).
Pull the shoe plate (4) forward, rotate to the
centre and push it back into the 0° location.
Push the blade support roller (5) forward until it
touches the saw blade (7).
Tighten the screws (8).
Variable speed control
The tool has a variable speed on/off switch (1).
The operating speed depends on how far you
press the switch.
Use a high speed for wood, medium speed for
aluminium and PVC and low speed for metals
other than aluminium.
Switching on and off
To switch the tool on, press the on/off switch
(1).
To switch the tool off, release the on/off switch
(1).
For continuous operation, press the lock-on
button (2) and release the on/off switch (1).
To switch the tool off when in continuous
operation, press and release the on/off switch
(1).
Hints for optimum use
Hold the tool fi rmly with both hands while
cutting.
The shoe should be held fi rmly against the
material being cut. This will help prevent
the saw from jumping, reduce vibration and
minimise blade breakage.
Let the blade run freely for a few seconds
before starting the cut.
Apply only a gentle pressure to the tool while
performing the cut.
Sawing laminates
When cutting laminates splintering may occur
which can damage the presentation surface. The
most common saw blades cut on the upward
stroke, therefore if the shoe plate is sitting on the
presentation surface either use a saw blade that
cuts on the downward stroke or:
Use a fi ne-tooth saw blade.
Saw from the back surface of the workpiece.
Clamp a piece of scrap wood or hardboard
to both sides of the workpiece to minimise
splintering, and saw through this sandwich.
Sawing metal
Be aware that sawing metal takes much more
time than sawing wood.
Use a saw blade suitable for sawing metal.
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker KS601E T1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker KS601E T1 in the language / languages: Polish, Turkish as an attachment in your email.

The manual is 1,84 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Black Decker KS601E T1

Black Decker KS601E T1 User Manual - English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish - 76 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info