580886
7
Zoom out
Zoom in
Previous page
1/76
Next page
7
ENGLISH
Warning! The vibration emission value during actual use of
the power tool can differ from the declared value depending
on the ways in which the tool is used. The vibration level may
increase above the level stated.
When assessing vibration exposure to determine safety
measures required by 2002/44/EC to protect persons regularly
using power tools in employment, an estimation of vibration
exposure should consider, the actual conditions of use and the
way the tool is used, including taking account of all parts of the
operating cycle such as the times when the tool is switched off
and when it is running idle in addition to the trigger time.
Labels on tool
The following pictograms are shown on the tool:
:
Warning! To reduce the risk of injury, the user must
read the instruction manual.
Electrical safety
#
This tool is double insulated; therefore no earth wire
is required. Always check that the power supply
corresponds to the voltage on the rating plate.
u If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised Black & Decker Service
Centre in order to avoid a hazard.
Features
This tool includes some or all of the following features:
1. On/off switch
2. Lock-on button
3. Dust extraction outlet
4. Shoe plate
5. Saw blade support roller
Fig. E
6. Saw blade storage compartment (KS602E & KS603E)
Assembly
Warning! Before attempting any of the following operations,
make sure that the tool is switched off and unplugged and that
the saw blade has stopped. Used saw blades may be hot.
Adjustingthesawbladesupportroller(g.A&B)
u Loosen the two screws (8).
u Push the blade support roller (5) forward until it touches
the back edge of the saw blade (7).
u Tighten the two screws (8).
Fittingandremovingthesawblade(g.C)
u Before tting or removing the saw blade (7) the saw blade
support roller (5) must be adjusted to the rear position so
that it does not contact the blade.
u Loosen (do not remove) the two screws (10).
u Hold the saw blade (7) with the teeth facing forward.
u Insert the shank of the saw blade (7) into the blade holder
(9) as far as it will go.
u Slightly tighten the two screws (10) alternately to position
the blade, then fully tighten the two screws (10).
u Adjust the saw blade support roller (5) as described above.
u To remove the saw blade (7), turn both screws (10) one
turn counter-clockwise.
Connectingavacuumcleanertothetool(g.D)
An adaptor (11) is required to connect a vacuum cleaner or
dust extractor to the tool. The adaptor can be purchased from
your local Black & Decker retailer.
u Push the adaptor (11) into the dust extraction outlet (3).
u Connect the vacuum cleaner hose (12) to the adaptor (11).
Sawbladestorage(KS602E&KS603Eonly)(g.E)
Saw blades (7) can be stored in the storage compartment (6)
located on the side of the tool
u Open the cover of the saw blade storage compartment (6)
by holding the tab on the top of the door and pulling outwards.
u Remove or store saw blades (7) in the storage
compartment (6).
u Close the cover of the saw blade storage compartment (6)
and make sure that it is latched closed.
Cutlineblower(g.F)
u To aid visibility when cutting, your jigsaw is equipped with
a cut line blower (13) which will keep the work area clear
of dust as you saw.
Use
Adjustingtheshoeplateforbevelcuts(g.G)
The shoe plate can be set to make either a straight cut or a
left or right bevel cut at an angle of 45°.
u Loosen the screws (8).
u Pull the shoe plate (4) forward, rotate the shoe plate (4) to
the left or right and push it back into the 45° location.
u Push the blade support roller (5) forward until it touches
the saw blade (7).
u Tighten the screws (8).
To reset the shoe plate for straight cuts:
u Loosen the screws (8).
u Pull the shoe plate (4) forward, rotate to the centre and
push it back into the 0° location.
u Push the blade support roller (5) forward until it touches
the saw blade (7).
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker KS601E T1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker KS601E T1 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,25 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Black Decker KS601E T1

Black Decker KS601E T1 User Manual - Polish, Turkish - 76 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info