579746
8
Zoom out
Zoom in
Previous page
1/16
Next page
8
Electrical safety
#
This tool is double insulated; therefore no earth wire
is required. Always check that the power supply
corresponds to the voltage on the rating plate.
u If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised Black & Decker Service
Centre in order to avoid a hazard.
Additional safety instructions for lasers
+
Read all of this manual carefully.
This product is not to be used by children under 16.
Warning! Laser radiation.
Do not look into the laser beam.
Do not view the laser beam directly with optical
instruments.
per IEC60825-1:2001
Pmax < 2.2mW 630-675nm
Refer to the laser product characteristics.
u This laser complies with class 2 according to
IEC60825-1:2007. Do not replace a laser diode with a
different type. If damaged, have the laser repaired by an
authorised repair agent.
u Do not use the laser for any purpose other than projecting
laser lines.
u An exposure of the eye to the beam of a class 2 laser is
considered safe for a maximum of 0.25 seconds.
Eyelid reflexes will normally provide adequate protection.
At distances over 1 m, the laser complies with class 1 and
thus is considered completely safe.
u Never look into the laser beam directly and intentionally.
u Do not use optical tools to view the laser beam.
u Do not set up the tool at a position where the laser beam
can cross any person at head height.
u Do not let children come near the laser.
Warning! The use of controls or adjustment or performance of
procedures other than those specied in these instructions
may result in exposure to hazardous laser radiation.
Warning! This tool is intended for indoor use only. Do not use
the tool for outdoor applications.
Features
1. On/off switch
2. Lock-off button
3. Main handle
4. Secondary handle
5. Spindle lock button
6. Laser on/off switch
7. Laser aperture
8. Shoe
9. Saw blade
10. Saw blade guard
11. Riving knife
12. Saw dust outlet
Assembly
Warning! Before attempting any of the following operations,
make sure that the tool is switched off and unplugged and that
the saw blade has stopped.
Removing and tting a saw blade (g. A)
Removing
u Keep the spindle lock button (5) depressed and rotate the
blade until the spindle lock engages.
u Loosen and remove the blade retaining screw (13) by
turning it counterclockwise using the spanner (14)
supplied.
u Remove the outer washer (15).
u Remove the saw blade (9).
Fitting
u Place the saw blade onto the inner flange (16), making
sure that the arrow on the blade points in the same
direction as the arrow on the tool.
u Fit the outer washer (15) on the spindle, with the raised
part pointing away from the saw blade.
u Insert the blade retaining screw (13) into the hole.
u Keep the spindle lock button (5) depressed.
u Securely tighten the blade retaining screw by turning it
clockwise using the spanner (14) supplied.
u Adjust the riving knife as described below.
Adjusting the riving knife (g. B)
The riving knife prevents the saw blade from jamming during
rip sawing operations. The riving knife must be adjusted after
replacing the saw blade.
u Loosen the screws (17), using the spanner (14), while
holding the riving knife in position.
u Position the riving knife (11) as shown.
u The distance between the toothed rim and the riving knife
should be 2 - 3 mm.
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker KS1600LK T2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker KS1600LK T2 in the language / languages: English as an attachment in your email.

The manual is 0,66 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Black Decker KS1600LK T2

Black Decker KS1600LK T2 User Manual - English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish - 108 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info