579740

Black Decker KS1401L T2 Manual

9
Zoom out
Zoom in
Previous page
1/108
Next page
9
ENGLISH
u The height difference between the toothed rim and the
lower end of the riving knife should be 2 - 3 mm.
u Tighten the screws.
Fittingandremovingtheparallelfence(g.C)
u The parallel fence is used to saw in a straight line parellel
to the edge of the workpiece.
Fitting
u Loosen the locking knob (18).
u Insert the parallel fence (19) through the openings (20).
u Slide the parallel fence into the desired position.
u Tighten the locking knob.
Removing
u Loosen the locking knob.
u Pull the parallel fence off the tool.
Use
Warning! Let the tool work at its own pace. Do not overload.
This tool can be used in the right hand or the left hand.
Adjustingthesawingangle(g.D)
The default angle between the saw blade and the shoe is 90°.
u Use a square to check that the angle between the saw
blade and the shoe is 90°. If the angle does not measure
90° adjust as follows:
u Loosen the locking knob (21) to unlock the saw shoe.
u Loosen the locknut (22) on the adjusting screw (23).
u Screw the adjusting screw in or out to achieve a 90° angle.
u Retighten the locknut.
u Tighten the locking knob to lock the saw shoe in place.
Adjustingthedepthofcut(g.E)
The depth of cut should be set according to the thickness of
the workpiece. It should exceed the thickness by approx.
2 mm.
u Loosen the knob (24) to unlock the saw shoe.
u Move the saw shoe (8) into the desired position.
The corresponding depth of cut can be read from the
scale (25).
u Tighten the knob to lock the saw shoe in place.
Adjustingthebevelangle(g.F)
This tool can be set to bevel angles between 0° and 45°.
u Loosen the locking knob (21) to unlock the saw shoe.
u Move the saw shoe (10) into the desired position.
The corresponding bevel angle can be read from the
scale (26).
u Tighten the locking knob to lock the saw shoe in place.
Switching on and off
u To switch the tool on, move the lock-off button (2) into the
unlock position and squeeze the on/off switch (1).
u To switch the tool off, release the on/off switch.
Sawing
Always hold the tool with both hands.
u Let the blade run freely for a few seconds before starting
the cut.
u Apply only a gentle pressure to the tool while performing
the cut.
u Work with the shoe pressed against the workpiece.
Hints for optimum use
u As some splintering along the line of cut on the top side of
the workpiece cannot be avoided, cut on the side where
splintering is acceptable.
u Where splintering is to be minimised, e.g. when cutting
laminates, clamp a piece of plywood onto the top of the
workpiece.
Usingthesightguide(g.G)
The tool is equipped with a sight guide for straight cutting (27)
and for 45° bevel cutting (28).
u Adjust the sight guide as described below.
u Align the left edge of the guides (27) or (28) with the
cutting line (29).
u Keep the sight guide aligned with the cutting line while
sawing.
u Work with the shoe pressed against the workpiece.
Adjusting the sight guide
u Make a test cut halfway through a piece of scrap wood.
u Withdraw the saw so the cutting line (29) becomes visible.
u While keeping the saw in this position, loosen the sight
guide on the saw shoe as shown.
u Align the 0° mark (27) on the sight guide with the cutting
line (29). When adjusting for 45° bevel cuts, align the 45°
mark (28) on the sight guide with the cutting line.
u Secure the sight guide using the screw (30).
Howtousethelaser(g.H)
The laser projects the line of cut on the workpiece surface.
u To switch the laser on, slide the switch (6) forward.
u To switch the laser off, slide the switch (6) backward.
Viewing from directly above the saw, the line of cut can be
easily followed. Should this view be restricted for any
reason, the laser can be used as an alternate cutting
guide.
u Use a pencil to mark the cutting line.
u Position the saw over the line.
u Switch on the laser.
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker KS1401L T2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker KS1401L T2 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,34 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Black Decker KS1401L T2

Black Decker KS1401L T2 Quick start guide - English - 16 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info