Manual Black Decker KS1400L T2 (page 7 of 108) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

579739

Zoom out

Zoom in

1/108

ENGLISH

Safety instructions for circular saws with outer or inner

pendulum guards and with tow guard

a. Check lower guard for proper closing before each

use. Do not operate the saw if lower guard does not

move freely and close instantly. Never clamp or tie the

lower guard into the open position. If saw is

accidentally dropped, lower guard may be bent. Raise the

lower guard with the retracting handle and make sure it

moves freely and does not touch the blade or any other

part, in all angles and depths of cut.

b. Check the operation of the lower guard spring. If the

guard and the spring are not operating properly, they

must be serviced before use. Lower guard may operate

sluggishly due to damaged parts, gummy deposits, or a

build-up of debris.

c. Lower guard should be retracted manually only for

special cuts such as "plunge cuts" and "compound

cuts". Raise lower guard by retracting handle and as

soon as blade enters the material, the lower guard

must be released. For all other sawing, the lower guard

should operate automatically.

d. Always observe that the lower guard is covering the

bladebeforeplacingsawdownonbenchoroor.An

unprotected, coasting blade will cause the saw to walk

backwards, cutting whatever is in its path. Be aware of the

time it takes for the blade to stop after switch is released.

Additional safety instructions for all saws with riving knife

Use the appropriate riving knife for the blade being

used. For the riving knife to work, it must be thicker than

the body of the blade but thinner than the tooth set of the

blade.

b. Adjust the riving knife as described in this instruction

manual. Incorrect spacing, positioning and alignment can

make the riving knife ineffective in preventing kickback.

c. Always use the riving knife except when plunge

cutting. Riving knife must be replaced after plunge

cutting. Riving knife causes interference during plunge

cutting and can create kickback.

d. For the riving knife to work, it must be engaged in the

workpiece. The riving knife is ineffective in preventing

kickback during short cuts.

e. Do not operate the saw if riving knife is bent. Even a

light interference can slow the closing rate of a guard.

Residual risks

The following risks are inherent to the use of saws:

- Injuries caused by touching the rotating parts.

Even with the application of the relevant safety regulations

and the implementation of safety devices, certain residual

risks cannot be avoided. These are:

- Impairment of hearing.

- Risk of accidents caused by the uncovered parts of the

rotating saw blade.

- Risk of injury when changing the blade.

- Risk of squeezing ngers when opening the guards.

- Health hazards caused by breathing dust developed

when sawing wood, especially oak, beech and MDF.

Saw blades

u Do not use blades of larger or smaller diameter than

recommended. For the proper blade rating refer to the

technical data. Use only the blades specified in this

manual, complying with EN 847-1.

u Warning! Never use abrasive wheels.

Safety of others

u This appliance is not intended for use by persons

(including children) with reduced physical, sensory or

mental capabilities, or lack of experience and knowledge,

unless they have been given supervision or instruction

concerning use of the appliance by a person responsible

for their safety.

u Children should be supervised to ensure that they do not

play with the appliance.

Vibration

The declared vibration emission values stated in the technical

data and the declaration of conformity have been measured in

accordance with a standard test method provided by

EN 60745 and may be used for comparing one tool with

another. The declared vibration emission value may also be

used in a preliminary assessment of exposure.

Warning! The vibration emission value during actual use of

the power tool can differ from the declared value depending

on the ways in which the tool is used. The vibration level may

increase above the level stated.

When assessing vibration exposure to determine safety

measures required by 2002/44/EC to protect persons regularly

using power tools in employment, an estimation of vibration

exposure should consider, the actual conditions of use and the

way the tool is used, including taking account of all parts of

the operating cycle such as the times when the tool is

switched off and when it is running idle in addition to the

trigger time.

Labels on tool

The following pictograms are shown on the tool:

Warning! To reduce the risk of injury, the user must

read the instruction manual.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker KS1400L T2 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,34 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Black Decker KS1400L T2

Black Decker KS1400L T2 Quick start guide - English - 16 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Black Decker KS1400L T2 Manual

Product: