580867
5
Zoom out
Zoom in
Previous page
1/72
Next page
5
ENGLISH
g. Use the power tool, accessories and tool bits etc., in
accordance with these instructions and in the manner
intended for the particular type of power tool, taking
into account the working conditions and the work to
be performed. Use of the power tool for operations
different from those intended could result in a hazardous
situation.
5. Service
a. Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will make sure that the safety of the power tool is
maintained.
Electrical safety
This tool is double insulated; therefore no earth
wire is required. Always check that the power
supply corresponds to the voltage on the rating
plate.
Additional safety instructions for non-rechargeable
batteries
X Never attempt to open for any reason.
X Do not store in locations where the temperature may
exceed 40 °C.
X When disposing of batteries, follow the instructions given
in the section "Protecting the environment".
Do not incinerate the batteries.
X Under extreme conditions, battery leakage may occur.
When you notice liquid on the batteries, proceed as
follows:
- Carefully wipe the liquid off using a cloth. Avoid skin
contact.
Additional safety instructions for lasers
Read all of this manual carefully.
This product is not to be used by children
under 16.
Laser radiation.
Do not look into the laser beam.
Do not use optical tools to view the laser
beam.
X This laser complies with class 2 according to IEC
60825+A1+A2:2001. Do not replace a laser diode with a
different type. If the laser is damaged, have the laser
repaired by an authorised repair agent.
X Do not use the laser for any purpose other than projecting
laser lines.
X An exposure of the eye to the beam of a class 2 laser is
considered safe for a maximum of 0.25 seconds. Eyelid
reflexes will normally provide adequate protection. At
distances greater than 1m, the laser complies with class 1
and is therefore considered completely safe.
X Never look into the laser beam directly and intentionally.
X Do not use optical tools to view the laser beam.
X Do not set up the tool where the laser beam can cross any
person at head height.
X Do not let children come near the laser.
Additional safety instructions for jigsaws
Warning! Contact with, or inhalation of dusts arising from
cutting applications may endanger the health of the operator
and possible bystanders. Wear a dust mask specifically
designed for protection against dust and fumes and ensure that
persons within or entering the work area are also protected.
Features
This tool includes some or all of the following features:
1. Variable speed control knob
2. Lock-on button
3. On/off switch
4. Side handle
5. Saw blade storage compartment
6. Turbo selector
7. Shoe plate locking knob
8. Shoe plate
9. Dust extraction adaptor
10. Saw blade
11. Saw blade support roller
12. Saw blade locking lever
13. Laser module (not supplied with KS1000NL)
Assembly
Warning! Before attempting any of the following operations,
make sure that the tool is switched off and unplugged and that
the saw blade has stopped. Used saw blades may be hot.
Fitting the saw blade (fig. A)
X Hold the saw blade (10) as shown, with the teeth facing
forward.
X Push the lever (12) downwards.
X Insert the shank of the saw blade into the blade holder (14)
as far as it will go.
X Release the lever (12).
Fitting and removal of the side handle (fig. B)
X The side handle (4) can be fitted to either the left or right
side of the tool.
X Align and insert the side handle (4) into the location on the
tool, then rotate it towards the rear until it locks into place.
X To remove, rotate it towards the front until it stops, then
pull it out of the location.
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker KS1000E T1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker KS1000E T1 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,42 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Black Decker KS1000E T1

Black Decker KS1000E T1 Quick start guide - English - 12 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info