383576
6
Zoom out
Zoom in
Previous page
1/64
Next page
6
ENGLISH
Always ensure the unit is unplugged from the power
supply when changing blades.
Always ensure the tooth protector is fitted when
changing blades.
REMOVING THE BLADE
Ensure blade has cooled
after use. Press and hold
the rear of the blade
release button fully, hold
the back of the blade
and rotate the blade
through 90° as shown in
the diagram. Slide the
blade sideways off the
retaining pin and remove
from the saw.
FITTING A BLADE
Place the blade with the
tooth protector fitted
over the location pin.
The blade teeth should
be facing the handle.
Rotate the blade
through 90° until it is
fully located in the slot
and the location pin is
in the locked position.
To ensure the blade is
securely fitted try to
remove without pressing
the blade release button.
Remove the tooth
protector, your saw is
now ready for use.
Note: If you are unable to fit the blade, check if the
location pin is in the correct position as shown
below. If it is not, keep the blade release button
depressed and use a screwdriver to turn the location
pin into the correct position.
OPERATING YOUR SCORPION SAW
Variable speed trigger switch
Your Scorpion Saw is equipped with a variable speed
trigger switch that allows you greater control over
start of cut, rate of cut and breakthrough of cut.
To switch your Scorpion
Saw on, push lock-off
button (2) and squeeze
the on/off variable
speed trigger switch (1).
To switch off, release
the trigger, the unit will
automatically lock-off.
Standard Mode
To obtain the best results
from your Scorpion Saw,
use the same backward
and forward movement
you would employ with
a traditional hand saw.
This will enable a quicker cleaner cut.
Operating in Jigsaw Mode
Disconnect unit from
power supply. Remove
blade, rotate shoe
through 270˚ and secure
in position. Fit curve
cutting blade.
Remove tooth protector
and your Scorpion Saw
is now ready for use.
Cutting Metal
Your Scorpion Saw can be used for cutting light
gauge ferrous and non-ferrous metals such as
copper, brass, aluminium, etc. See recommended
materials.
It is advisable when cutting thin sheet to clamp a
backing sheet of soft wood or plywood to the work
as this will enable you to obtain a cleaner cut. Both
metal and wood backing are sawn together. Do not
force the cutting blade into the metal as this will
reduce the life of the blade and possibly damage the
motor. Cutting thin metal will take longer than cutting
even a relatively thick piece of wood, so do not be
tempted to speed up the operation by forcing the
saw. Spread a thin film of oil along the proposed
cutting line before cutting.
Only use the metal cutting blade for this purpose.
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker ks 890 e scorpion at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker ks 890 e scorpion in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,73 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info