382814

Black Decker ks 710 l Manual

6
Zoom out
Zoom in
Previous page
1/68
Next page
6
ENGLISH
Hold the saw blade (13) as shown, with the teeth facing
forward.
Insert the shank of the saw blade into the blade holder (14)
as far as it will go.
Tighten the screw (12).
Fitting and removing the parallel fence (fig. B)
the parallel fence is used to saw in a straight line parellel to
the edge of the workpiece. The fence can be fitted both to the
left side and to the right side.
Fitting
Loosen the locking knob (15).
Insert the parallel fence (16) through the openings (17).
Slide the parallel fence into the desired position.
Tighten the locking knob.
Removing
Loosen the locking knob (15).
Pull the parallel fence off the tool.
Connecting a vacuum cleaner to the tool (fig. C)
Slide the dust extraction adaptor (10) into the shoe plate (8)
until it locks in position.
Connect the vacuum cleaner hose (18) to the adaptor (10).
Make sure that the dust shroud (6) is fitted.
Use
Warning! Let the tool work at its own pace. Do not overload.
Adjusting the shoe plate for bevel cuts (fig. D)
The shoe plate can be set to a left or right bevel angle of up to
45°.
Remove the dust extraction adaptor (10) if fitted.
Loosen the screw (19).
Pull the shoe plate (8) forward, set it to the required angle
and push it back into place. You can use the scale or a
protractor to check the angle.
Tighten the screw (19).
To reset the shoe plate for straight cuts:
Loosen the screw (19).
Pull the shoe plate forward and set it to an angle of
approx. 0°.
Push the shoe plate backward and tighten the screw (19).
Use a square to check the angle.
Setting the pendulum stroke
Set the pendulum stroke selector (9) to the desired position.
Position 0: for laminates and sheet metal
Position 1-2: for plywood, metal and aluminium
Position 2-3: for soft wood and pvc
Variable speed control
Set the variable speed control knob (3) to the required
speed range. Use a high speed for wood, medium speed
for aluminium and PVC and low speed for metals other
than aluminium.
Switching on and off
To switch the tool on, press the on/off switch (1).
For continuous operation, press the lock-on button (2) and
release the on/off switch.
To switch the tool off, release the on/off switch. To switch
the tool off when in continuous operation, press the on/
off switch once more and release it.
Hints for optimum use
Sawing laminates
As the saw blade cuts on the upward stroke, splintering may
occur on the surface closest to the shoe plate.
Use a fine-tooth saw blade.
Saw from the back surface of the workpiece.
To minimise splintering, clamp a piece of scrap wood or
hardboard to both sides of the workpiece and saw through
this sandwich.
Sawing metal
Be aware that sawing metal takes much more time than
sawing wood.
Use a saw blade suitable for sawing metal.
When cutting thin sheet metal, clamp a piece of scrap
wood to the back surface of the workpiece and cut
through this sandwich.
Spread a film of oil along the intended line of cut.
How to use the laser (fig. E)
the laser projects the line of cut on the workpiece surface.
To switch the laser on, press the button (4).
To switch the laser off, press the button (4) again.
viewing from directly above the saw, the line of cut can be
easily followed. Should this view be restricted for any reason,
the laser can be used as an alternate cutting guide.
Use a pencil to mark the cutting line.
Position the saw over the line.
Switch on the laser.
Maintenance
Your tool has been designed to operate over a long period of
time with a minimum of maintenance. Continuous satisfactory
operation depends upon proper tool care and regular cleaning.
Warning! Before performing any maintenance, switch off and
unplug the tool.
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker ks 710 l at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker ks 710 l in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,4 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info