382645

Black Decker ks 631 Manual

7
Zoom out
Zoom in
Previous page
1/12
Next page
7
ENGLISH
All models
Note: To achieve a greater accuracy of cut, ensure
back of blade is touching blade support roller. See
‘Blade suport roller’ for instructions on how to change
position of blade support roller.
BLADE SUPPORT ROLLER
To provide greater support and accuracy when cutting,
your jigsaw is fitted with a blade support roller. This
support should be adjusted so that the roller touches
the back of the blade when cutting.
To do this, loosen the front
screw on the base of the
shoe. Push the blade
support forward until the
roller touches the back
edge of the blade. Retighten
the screw. Lubricating the
guide roller (5) from time to time with a drop of oil will
extend the life of the roller.
For scroller jigsaws only
Note: When using your jigsaw in the scrolling mode,
the blade support roller needs to be retracted to allow
free movement of the blade.
To do this, untighten the
front screw on the base of
the shoe and retract the
support. Re-tighten the
screw.
OPERATING YOUR JIGSAW
To switch your jigsaw on, fully squeeze the on/off
trigger switch (1). To switch your jigsaw off, release
the trigger switch (1). When plugging your jigsaw in,
ensure the trigger switch is in the OFF position.
When continuous operation is required, squeeze the
trigger and depress the lock on button (2) and release
the trigger. To disengage the lock, squeeze and release
the trigger. Always disengage the lock before
disconnecting from the power supply.
SAW SHOE ADJUSTMENT FOR ANGULAR CUTTING
The shoe plate (6) can be angled up to 45˚ on either side.
To do this, disconnect your jigsaw from the power supply.
Raise or remove the dust
shroud (4) and loosen both
screws on the shoe plate
with a screwdriver. Pull the
shoe plate backward a little,
and set the desired angular
adjustment according to the
scale or push the shoe plate
forward for fixed locks at 0˚,
15˚, 30˚, or 45˚. Tighten the
screws to secure. Although
the scale and notches are
accurate for most purposes
it is advisable for very
accurate angle cutting to use a protractor to set the
shoe. Make a test cut on some scrap material to check
the accuracy of the angle. To reset the shoe for a
square cut, slacken the clamp screws and move the
shoe until it is approximately 90˚ to the blade, and then,
whilst applying slight forward pressure on the shoe,
retighten the clamp screws. If necessary, re-adjust the
bade support roller using only the front screw.
DUST BLOWING
To aid visibility when cutting,
your jigsaw is fitted with a
facility which will blow dust
away from surface of
material being cut. To utilise,
lift up or remove dust visor
and ensure the variable
blower control is pointing towards the symbol.
DUST EXTRACTION
Your jigsaw with a hose adapter (accessory part), can
be fitted to most portable vacuum cleaners.
To utilise this facility push
adapter into the aperture at
the rear of jigsaw and fit
vacuum hose in or over the
adapter, depending on the
hose size. The dust shroud
should be attached and in a
downwards position and
the variable blower control
on the side of the jigsaw
should point towards the
symbol.
ELECTRONIC SPEED REGULATION
For electronic models only
The electronic speed
control wheel (3) is used to
programme the required
saw speed depending on
the material being worked.
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker ks 631 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker ks 631 in the language / languages: English as an attachment in your email.

The manual is 0,59 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Black Decker ks 631

Black Decker ks 631 User Manual - English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Spanish, Norwegian, Finnish - 68 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info