382775
28
Zoom out
Zoom in
Previous page
1/80
Next page
28
ENGLISH
When attempting mitre cuts, follow the same
procedure detailed above, however, use the area
marked 45˚ on the ‘sight guide’.
ADJUSTING THE PARALLEL FENCE
Your circular saw includes a parallel fence. This permits
the sawing of a straight line parallel to the edge of the
workpiece. To assemble and adjust the parallel fence,
proceed as follows:
Disconnect the plug from the electricity supply.
Loosen the locking screw
(15) at the forward end of
the saw base. Slide the
parallel fence (8) along
its guide until the desired
measurement is indicated. Tighten the locking screw (15).
SETTING THE MITRING ADJUSTMENT
Your circular saw can cut at angles up to 45˚. To adjust
the angle of your circular saw, proceed as follows:
Disconnect the plug from the electricity supply.
Loosen the locking
screw (13). Loosen the
locking lever (22) if fitted
on your product. Move
your circular saw around
the mitre scale (12) until
the desired angle is
indicated. Tighten the locking screw (13). Tighten the
locking lever (22) if fitted on your product.
CHANGING THE BLADE
Proceed as follows:
Disconnect the plug from the electricity supply.
Retract the blade guard
(7). Insert a screwdriver
through the hole in the
blade to prevent rotation
of the blade.
Unlock and remove
screw (5). Loosen
anticlockwise using a
13mm spanner, remove
the outer washer (24)
and remove the blade.
Insert the new blade,
ensuring that the arrow
on the blade points in the same direction as the arrow
on the body of your circular saw. Fit the outer washer
(24) with the raised centre portion pointing away from
the blade. Ensure that this washer is correctly located on
the flats of the spindle. Fit the saw blade locking screw
(5). Insert a screwdriver through the hole in the blade
to prevent rotation of the blade. Tighten the sawblade
locking screw clockwise using a 13mm spanner.
ADJUSTING THE RIVING KNIFE
The riving knife (6) prevents the saw blade from
jamming during rip sawing operations. You must check
the position of the riving knife whenever the saw blade
is replaced, or whenever the clearance is affected.
Proceed as follows:
Disconnect the plug from the electricity supply.
Through the opening in
the blade guard, locate
the two riving knife
screws.
If your circular saw
does not have an
opening in the blade
guard, adjust the cutting
depth to locate the
riving knife screws.
Loosen the two riving
knife screws. Adjust the
riving knife to give a radial clearance of 2-3mm and a
tooth peak clearance of 2-3mm. Tighten the two riving
knife screws.
Your saw is now ready for use.
OPERATING YOUR CIRCULAR SAW
To switch your circular
saw on, depress the
lock-off button (25) and
squeeze the on/off
trigger switch (20).
To stop your circular
saw, release the
trigger switch.
HOLDING YOUR CIRCULAR SAW
The front handle (10) makes it easier to guide the saw
properly. Switch the machine on before you start
sawing the workpiece. Guide the saw without pushing
3mm
2
m
m
6
22
13
12
7
26
5
24
23
8
15
CD600 Circ saw ML p01-41 07/01/2000, 3:43 pm28
28


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker ks 227 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker ks 227 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,78 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Black Decker ks 227

Black Decker ks 227 User Manual - English - 35 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info