Manual Black Decker ks 1300 (page 8 of 96) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Spanish, Norwegian, Finnish)

383517

Zoom out

Zoom in

1/96

ENGLISH

Electrical safety

This tool is double insulated; therefore no earth wire

is required. Always check that the power supply

corresponds to the voltage on the rating plate.

u If the supply cord is damaged, it must be replaced by the

manufacturer or an authorised Black & Decker Service

Centre in order to avoid a hazard.

Features

1. On/off switch

2. Lock-off button

3. Main handle

4. Secondary handle

5. Spindle lock button

6. Shoe

7. Saw blade

8. Saw blade guard

9. Riving knife

10. Saw dust outlet

Assembly

Warning! Before attempting any of the following operations,

make sure that the tool is switched off and unplugged and that

the saw blade has stopped.

Removingandttingasawblade(g.A)

Removing

u Keep the spindle lock button (5) depressed and rotate the

blade until the spindle lock engages.

u Loosen and remove the blade retaining screw (11) by

turning it counterclockwise using the spanner (12)

supplied.

u Remove the outer washer (13).

u Remove the saw blade (7).

Fitting

u Place the saw blade onto the inner flange (14), making

sure that the arrow on the blade points in the same

direction as the arrow on the tool.

u Fit the outer washer (13) on the spindle, with the raised

part pointing away from the saw blade.

u Insert the blade retaining screw (11) into the hole.

u Keep the spindle lock button (5) depressed.

u Securely tighten the blade retaining screw by turning it

clockwise using the spanner (12) supplied.

u Adjust the riving knife as described below.

Adjustingtherivingknife(g.B)

The riving knife prevents the saw blade from jamming during

rip sawing operations. The riving knife must be adjusted after

replacing the saw blade.

u Loosen the screws (15), using the spanner (12), while

holding the riving knife in position.

u Position the riving knife (9) as shown.

u The distance between the toothed rim and the riving knife

should be 2 - 3 mm.

u The height difference between the toothed rim and the

lower end of the riving knife should be 2 - 3 mm.

u Tighten the screws.

Fittingandremovingtheparallelfence(g.C)

u The parallel fence is used to saw in a straight line parellel

to the edge of the workpiece.

Fitting

u Loosen the locking knob (16).

u Insert the parallel fence (17) through the openings (18).

u Slide the parallel fence into the desired position.

u Tighten the locking knob.

Removing

u Loosen the locking knob.

u Pull the parallel fence off the tool.

Use

Warning! Let the tool work at its own pace. Do not overload.

This tool can be used in the right hand or the left hand.

Adjustingthesawingangle(g.D)

The default angle between the saw blade and the shoe is 90°.

u Use a square to check that the angle between the saw

blade and the shoe is 90°. If the angle does not measure

90° adjust as follows:

u Loosen the locking knob (19) to unlock the saw shoe.

u Loosen the locknut (20) on the adjusting screw (21).

u Screw the adjusting screw in or out to achieve a 90° angle.

u Retighten the locknut.

u Tighten the locking knob to lock the saw shoe in place.

Adjustingthedepthofcut(g.E)

The depth of cut should be set according to the thickness of

the workpiece. It should exceed the thickness by approx.

2 mm.

u Loosen the knob (22) to unlock the saw shoe.

u Move the saw shoe (6) into the desired position.

The corresponding depth of cut can be read from the

scale (23).

u Tighten the knob to lock the saw shoe in place.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker ks 1300 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,21 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Black Decker ks 1300 Manual

Product: