Manual Black Decker KR700CRE T4 (page 25 of 68) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Spanish, Norwegian, Finnish)

601822

Zoom out

Zoom in

1/68

depth stop and the end of the drill bit is equal to the

length of the screw you will fit. Tighten the side handle.

PREPARING YOUR DRILL FOR OPERATION

Proceed as follows:

Fit the correct accessory for the job.

Set the speed of

your drill by

setting the

variable speed

control to the

desired position.

As a general rule,

for large size drill bits use low speeds and for smaller

drill bits use high speeds.

Set the forward/

reverse switch to

the desired

direction of

rotation. Never

change the setting

of the hammer/

drill switch, the variable speed control or the forward/

reverse switch when your drill is in operation.

USING YOUR DRILL

To switch your

drill on, depress

the on/off switch.

Your drill stops

when the switch

is released.

If continuous

operation is

required, depress

the lock-on button

while the on/off

switch is

depressed. To stop

your drill when

operation is

continuous, depress the switch again and release.

While your drill is in operation, do not touch the chuck.

HANDY HINTS

• Fit the correct size and type of drill or screwdriver bit.

• Always hold your drill using the handle and the

side handle.

• Always hold your drill at right-angles to your work.

When drilling

wood and metal,

set the hammer/

drill switch to the

drill mode .

When drilling

masonry, set the

hammer/drill

switch to the

hammer mode . When screwdriving, set the

hammer/drill switch to the drill mode .

• Set the forward/reverse switch to the correct direction.

• Never change the direction of rotation when your

drill is in operation.

• After use, remove the drill bit and gently tap the side

of the chuck with a soft-faced hammer to remove

the dust. This will extend the life of the chuck.

COOLING DOWN

If your drill becomes too hot in use, set the variable

speed control to its highest setting and allow your drill

to operate without load for 2 minutes.

OVERLOAD

Never use excessive force when using your drill. Too

much pressure can reduce the speed of your drill and

reduce its efficiency. This can result in an overload

which can cause damage to the motor of your drill.

EC DECLARATION OF CONFORMITY

We declare that units: KR580RE, KR580CRE, KR650RE,

KR650CRE, KR700RE, KR700CRE conform to 98/37/EC,

89/336/EEC, EN55014, 73/23/EEC, EN55104, EN50144

A weighted sound pressure 99dB (A)

A weighted sound power 112dB (A)

Hand/arm weighted vibration 8.89m/s

Brian Cooke - Director of Engineering

Black & Decker Ltd, Spennymoor, County Durham

DL16 6JG United Kingdom

The Black & Decker policy is one of continuous

improvement to our product and as such we reserve

the right to change the product specification without

prior notice.

ENGLISH

KR580-700 ML p21-35 05-02-2001, 10:4825

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker KR700CRE T4 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 8,84 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Black Decker KR700CRE T4 Manual

Product: