601798
8
Zoom out
Zoom in
Previous page
1/76
Next page
8
ENGLISH
ASSEMBLY
Before attempting any of the following
operations, make sure that the tool is
switched off and unplugged.
Fitting the side handle (fig. B)
Turn the grip (9) counterclockwise until you can
slide the side handle (5) onto the front of the
tool as shown.
Rotate the side handle into the desired position.
Tighten the side handle by turning the grip
clockwise.
Fitting a drill bit or screwdriver bit
Keyless chuck (fig. C)
Open the chuck by turning the front part (10)
with one hand while holding the rear part (11)
with the other.
Insert the bit shaft (12) into the chuck and
firmly tighten the chuck.
Keyed chuck (fig. D)
Open the chuck by turning the sleeve (13).
Insert the bit shaft (12) into the chuck.
Insert the chuck key (14) into each hole (15) in
the side of the chuck and turn until tight.
Removing and refitting the chuck (fig. E)
Open the chuck as far as possible.
Remove the chuck retaining screw by turning it
clockwise using a screwdriver.
Tighten an Allen key (16) into the chuck and
strike it with a hammer as shown.
Remove the Allen key.
Remove the chuck by turning it counterclockwise.
To refit the chuck, screw it onto the spindle
and secure it with the chuck retaining screw.
USE
Let the tool work at its own pace.
Do not overload.
Before drilling into walls, floors or
ceilings, check for the location of wiring
and pipes.
Selecting the direction of rotation (fig. A)
For drilling and for tightening screws, slide the
forward/reverse switch (7) forward.
For loosening screws or removing a jammed
drill bit, slide the forward/reverse switch (7)
backward.
Never change the direction of rotation
while the motor is running.
Selecting the drilling mode (fig. A)
For drilling in masonry, set the drilling mode
selector (4) to the position.
For drilling in other materials and for
screwdriving, set the drilling mode selector (4)
to the position.
Switching on and off (fig. A)
Variable speed switch
To switch the tool on, press the variable speed
switch (1). The tool speed depends on how far
you press the switch. As a general rule, use low
speeds for large diameter drill bits and high
speeds for smaller diameter drill bits.
For continuous operation, press the lock-on
button (2) and release the variable speed switch.
This option is available only at full speed.
To switch the tool off, release the variable
speed switch. To switch the tool off when in
continuous operation, press the variable speed
switch once more and release it.
On/off switch
To switch the tool on, press the on/off switch (1).
If the tool has a two-speed selector (3), set it to
the required speed range. As a general rule,
use low speeds for large diameter drill bits and
high speeds for smaller diameter drill bits.
For continuous operation, press the lock-on
button (2) and release the on/off switch.
To switch the tool off, release the on/off
switch. To switch the tool off when in
continuous operation, press the on/off switch
once more and release it.
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker KR531 T2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker KR531 T2 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,69 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info