386366
4
Zoom out
Zoom in
Previous page
1/60
Next page
4
ENGLISH
Use of the power tool for operations different from those
intended could result in a hazardous situation.
5. Service
a. Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
Additional safety instructions for impact drills
Wear ear protectors with impact drills. Exposure to
noise can cause hearing loss.
Use auxiliary handles supplied with the tool. Loss of
control can cause personal injury.
Electrical safety
This tool is double insulated; therefore no earth wire
is required. Always check that the power supply
corresponds to the voltage on the rating plate.
This appliance is not intended for use by young or infirm
persons without supervision. Children must be supervised
to ensure they do not play with the appliance.
If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised Black & Decker Service
Centre in order to avoid a hazard.
Features
This tool includes some or all of the following features.
1. Variable speed switch
2. Lock-on button
3. Forward/reverse slider
4. Levelok
straight drilling indicator
5. Drilling mode selector
6. Keyless chuck (KR60(L)/KR70(L))
Quick Connect
chuck (KR60QC/KR70QC)
7. Depth stop
8. Side handle
9. Bit storage
Assembly
Warning! Make sure that the tool is switched off and unplugged.
Fitting the side handle and depth stop (fig. A)
Turn the grip (10) counterclockwise until you can slide the
side handle (8) onto the front of the tool as shown.
Rotate the side handle into the desired position.
Insert the depth stop (7) into the mounting hole as shown.
Set the depth stop to the desired position. The maximum
drilling depth is equal to the distance between the tip of
the drill bit and the front end of the depth stop.
Tighten the side handle by turning the grip clockwise.
Fitting a drill bit or screwdriver bit
KR60(L)/KR70(L) - Keyless chuck (fig. B)
Open the chuck by turning the front part (12) with one
hand while holding the rear part (11) with the other.
Insert the bit shaft (13) into the chuck and firmly tighten
the chuck.
KR60QC/KR70QC - Quick Connect
chuck (fig. B & C)
The chuck on these models can be easily removed and refitted.
When your project entails both drilling and screwdriving,
fit a screwdriver bit in the spindle and a drill bit in the chuck:
you will then only need to remove the chuck for screwdriving
and refit it for drilling. The screwdriver bit can be left in the
spindle while drilling. You can also fit drill bits with a
hexagonal shaft in this way.
To fit a drill bit, proceed as described above.
To fit a screwdriver bit, proceed as follows:
Remove the chuck (6).
Install a screwdriver bit (16) by pushing it into the spindle
(15) as shown.
To remove the screwdriver bit, pull the ring (17) back and
pull the screwdriver bit out of the spindle.
Removing and refitting the chuck
KR60(L)/KR70(L) - Keyless chuck (fig. D)
Open the chuck as far as possible.
Remove the chuck retaining screw, located in the front
part of the chuck, by turning it clockwise using a
screwdriver.
Tighten an Allen key (18) into the chuck and strike it with
a hammer as shown.
Remove the Allen key.
Remove the chuck by turning it counterclockwise.
To refit the chuck, screw it onto the spindle and secure it
with the chuck retaining screw.
KR60QC/KR70QC - Quick Connect
chuck (fig. C)
To remove the chuck (6), keep the release tabs (14)
depressed and pull the chuck off the spindle (15).
To refit the chuck, push it onto the spindle until it is firmly
locked into place.
Warning! Always make sure that the chuck is securely fitted.
Use
Warning! Before drilling into walls, floors or ceilings,
check for the location of wiring and pipes.
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker kr 60 k at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker kr 60 k in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Finnish as an attachment in your email.

The manual is 1,03 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info