388538

Black Decker kr 2000 k Manual

4
Zoom out
Zoom in
Previous page
1/52
Next page
4
ENGLISH
Features
This tool includes some or all of the following features (fig. A)
1. Variable speed switch
2. Lock-on button
3. Bit holder
4. Locking ring
5. Forward/reverse switch
6. Direction of rotation indicator
7. Torque adjustment collar
Assembly
Warning! Make sure that the tool is switched off and unplugged.
Fitting and removing a drill bit or screwdriver bit (fig. B)
Fitting
This tool uses screwdriver bits and drill bits with a 1/4" (6.35 mm)
hexagonal shank.
◆ Insert the bit shaft into the bit holder (3) and press it
down until it clicks in place.
Removing
Warning! The drill bit may be hot just after drilling.
◆ Pull the locking ring (4) backwards and take the bit out of
the bit holder.
Use
Warning! Before drilling into walls, floors or ceilings,
check for the location of wiring and pipes.
Selecting the direction of rotation (fig. C)
◆ For drilling and for tightening screws, move the forward/
reverse switch (5) to the right. The direction indicator (6)
shows a forward pointed arrow.
◆ For loosening screws or removing a jammed bit, move the
forward/reverse switch to the left. The direction indicator
shows a backward pointed arrow.
Warning! Never change the direction of rotation while the
motor is running.
Selecting the torque or drill position (fig. D)
This tool is fitted with a collar to set the torque for tightening
screws.
◆ For drilling, turn the collar (7) to the left until the symbol
aligns with the marking (8).
◆ For screwdriving, set the collar to the desired setting. If you
do not yet know the desired setting, proceed as follows:
◆ Turn the collar (7) completely to the right (lowest torque).
◆ Tighten the first screw.
◆ If the clutch ratchets before the desired result is
achieved, increase the torque by turning the collar to
the left. Continue tightening the screw. Repeat until
you reach the correct setting. Use this setting for the
remaining screws.
Switching on and off (fig. A)
◆ To switch the tool on, press the variable speed switch (1).
The tool speed depends on how far you press the switch.
As a general rule, use low speeds for large diameter drill
bits and high speeds for smaller diameter drill bits.
◆ For continuous operation, press the lock-on button (2) and
release the variable speed switch. This option is available
only at full speed.
◆ To switch the tool off, release the variable speed switch.
To switch the tool off when in continuous operation, press
the variable speed switch once more and release it.
Hints for optimum use
Drilling
◆ Always apply a light pressure in a straight line with the
drill bit.
◆ Just before the drill tip breaks through the other side of
the workpiece, decrease pressure on the tool.
◆ Use a block of wood to back up workpieces that may splinter.
◆ Use spade bits when drilling large diameter holes in wood.
◆ Use masonry drill bits when drilling into light masonry.
◆ Use HSS drill bits when drilling in metal.
◆ Use a lubricant when drilling metals other than cast iron
and brass.
◆ Make an indentation with a centre punch at the centre of
the hole to be drilled in order to improve accuracy.
Screwdriving
◆ Always use the correct type and size of screwdriver bit.
◆ If screws are difficult to tighten, try applying a small amount
of washing liquid or soap to the thread as a lubricant.
◆ Always hold the tool and screwdriver bit in a straight line
with the screw.
◆ When screwing in wood, it is recommended to drill a pilot
hole with a depth equal to the length of the screw.
◆ A pilot hole guides the screw and prevents splintering or
distortion of the wood. For the optimum size of the pilot
hole, refer to the table below.
◆ When screwing in hardwood, also drill a clearance hole with
a depth equal to half the length of the screw. For the
optimum size of the clearance hole, refer to the table below.
Screw size Pilot hole ø (softwood)
No. 6 (3.5 mm) 2 mm
No. 8 (4 mm) 3.2 mm
No. 10 (5 mm) 3.5 mm
Screw size Pilot hole ø (hardwood)
No. 6 (3.5 mm) 2.5 mm
No. 8 (4 mm) 3.5 mm
No. 10 (5 mm) 4.0 mm
… 4 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker kr 2000 k at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker kr 2000 k in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,77 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info