497038
10
Zoom out
Zoom in
Previous page
1/92
Next page
10
ENGLISH
KG70: Place the outer flange (12) onto the
spindle with the raised centre facing towards
the disc (A in fig. F).
KG68/KG75/CD500: Place the outer flange (12)
onto the spindle. When fitting a grinding disc,
the raised centre on the outer flange must face
towards the disc (A in fig. F). When fitting a
cutting disc, the raised centre on the outer
flange must face away from the disc (B in fig. F).
KG68/CD500: Hold the spindle using the
wrench (13) and tighten the outer flange using
the two-pin spanner (14) (fig. G).
KG70/KG75: Keep the spindle lock (3)
depressed and tighten the outer flange using
the two-pin spanner (14) (fig. A & G).
Removing
KG68/CD500: Hold the spindle using the
wrench (13) and loosen the outer flange (12)
using the two-pin spanner (14) (fig. G).
KG70/KG75: Keep the spindle lock (3)
depressed and loosen the outer flange (12)
using the two-pin spanner (14) (fig. A & G).
Remove the outer flange (12) and the disc (5).
Fitting and removing sanding discs (fig. A, H & I)
For sanding, a backing pad is required.
The backing pad is available from your
Black & Decker dealer as an accessory.
Fitting
Remove the guard as described above.
Place the inner flange (10) onto the spindle (6)
as shown (fig. H). Make sure that the flange is
correctly located on the flat sides of the spindle.
Place the backing pad (15) onto the spindle.
Place the sanding disc (16) onto the backing pad.
Place the outer flange (12) onto the spindle with
the raised centre facing away from the disc.
KG68/CD500: Hold the spindle using the
wrench (13) and tighten the outer flange using
the two-pin spanner (14) (fig. I).
KG70/KG75: Keep the spindle lock (3)
depressed and tighten the outer flange using
the two-pin spanner (14) (fig. A & I).
Removing
KG68/CD500: Hold the spindle using the
wrench (13) and loosen the outer flange (12)
using the two-pin spanner (14) (fig. I).
KG70/KG75: Keep the spindle lock (3)
depressed and loosen the outer flange (12)
using the two-pin spanner (14) (fig. A & I).
Remove the outer flange (12), the sanding disc
(16) and the backing pad (15).
After sanding, refit the guard on the tool.
USE
Let the tool work at its own pace.
Do not overload.
Carefully guide the cable in order to avoid
accidentally cutting it.
Be prepared for a stream of sparks when the
grinding or cutting disc touches the workpiece.
Always position the tool in such a way that the
guard provides optimum protection from the
grinding or cutting disc.
Switching on and off (fig. J)
To switch on, slide the on/off switch (1)
forward.
To switch off, press the rear part of the on/off
switch.
Hints for optimum use
Firmly hold the tool with one hand around the
side handle and the other hand around the
motor housing (fig. K).
When grinding, always maintain an angle of
approx. 15° between the disc and the
workpiece surface (fig. L).
MAINTENANCE
Your Black & Decker tool has been designed to
operate over a long period of time with a
minimum of maintenance. Continuous satisfactory
operation depends upon proper tool care and
regular cleaning.
SAG.P65 17-07-2001, 14:5110
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker KG70 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker KG70 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,84 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info