497033
8
Zoom out
Zoom in
Previous page
1/100
Next page
8
ENGLISH
(Original instructions)
Labels on tool
The following pictograms are shown on the tool:
:
Warning! To reduce the risk of injury, the user must
read the instruction manual.
O
Wear safety glasses or goggles when operating this
tool.
N
Wear ear protection when operating this tool.
Electrical safety
#
This tool is double insulated; therefore no earth wire
is required. Always check that the power supply
corresponds to the voltage on the rating plate.
u If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised Black & Decker Service
Centre in order to avoid a hazard.
Features
This tool includes some or all of the following features.
1. On/off switch
2. Lock-off button
3. Side handle
5. Spindle lock
5. Guard
Assembly
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
Fitting and removing the guard (g. A)
The tool is supplied with a guard intended for grinding
purposes only. If the unit is intended to perform cutting off
operations, a guard specic for this operation must be tted. A
suitable guard for cutting off operations part number 1004484-
03 is available and can be obtained from Black & Decker
service centres.
Fitting
u Place the tool on a table, with the spindle (6) facing up.
u Hold the guard (5) over the tool as shown.
u Align the holes in the adjusting plate (7) with the screw
holes (8).
u Press the guard down and insert the screws (9) into the
holes.
u Tighten the screws.
Removing
u Remove the screws (9).
u Remove the guard from the tool.
Warning! Never use the tool without the guard.
Adjusting the guard (g. B)
The guard can be rotated 180°.
u Slacken the screws (9) and the nut (10).
u Rotate the guard as required.
u Re-tighten the screws and the nut.
Fitting the side handle
u Screw the side handle (3) into one of the mounting holes
in the tool.
Warning! Always use the side handle.
Fitting and removing grinding or cutting discs (g.
C - F)
Always use the correct type of disc for your application.
Always use discs with the correct diameter and bore size (see
technical data). The maximum thickness for grinding discs is 6
mm, for cutting discs 3.5 mm.
Fitting
u Fit the guard as described above.
u Place the inner ange (11) onto the spindle (6) as shown
(g. C). Make sure that the ange is correctly located on
the at sides of the spindle.
u Place the disc (12) onto the spindle (6) as shown (g. D).
If the disc has a raised centre (13), make sure that the
raised centre faces the inner ange.
u Make sure that the disc locates correctly on the inner
ange.
u Place the outer ange (14) onto the spindle. When tting
a grinding disc, the raised centre on the outer ange must
face towards the disc (A in g. E). When tting a cutting
disc, the raised centre on the outer ange must face away
from the disc (B in g. E).
u Keep the spindle lock (4) depressed and tighten the outer
ange using the two-pin spanner (15) (g. F).
Removing
u Keep the spindle lock (4) depressed and loosen the outer
ange (14) using the two-pin spanner (15) (g. F).
u Remove the outer ange (14) and the disc (12).
Use
Warning! Let the tool work at its own pace. Do not overload.
u Carefully guide the cable in order to avoid accidentally
cutting it.
u Be prepared for a stream of sparks when the grinding or
cutting disc touches the workpiece.
u Always position the tool in such a way that the guard
provides optimum protection from the grinding or cutting
disc.
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker KG2000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker KG2000 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 2,01 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info