602312

Black Decker KD976KA T3 Manual

7
Zoom out
Zoom in
Previous page
1/76
Next page
7
ENGLISH
Fittingthesidehandleanddepthstop(g.A)
u Turn the grip counterclockwise until you can slide the side
handle (7) onto the front of the tool as shown.
u Rotate the side handle into the desired position.
u Insert the depth stop (8) into the mounting hole as shown.
u Set the depth stop to the desired position. The maximum
drilling depth is equal to the distance between the tip of
the drill bit and the front end of the depth stop.
u Tighten the side handle by turning the grip clockwise.
Fittinganaccessory(g.B)
u Clean and grease the shank (9) of the accessory.
u Pull back the sleeve (10) and insert the shank into the tool
holder (6).
u Push the accessory down and turn it slightly until it fits into
the slots.
u Pull on the accessory to check if it is properly locked.
The hammering function requires the accessory to be able
to move axially several centimetres when locked in the
tool holder.
u To remove the accessory, pull back the sleeve (10) and
pull out the accessory.
KD985/KD990-Fittingthekeyedchuck(g.C)
u Fit the shank (11) of the supplied chuck (12) into the tool
holder as described above.
Warning! Never use keyed chucks in the hammer drilling mode.
KD985/KD990 - Fitting accessories in the keyed
chuck(g.D)
u Open the chuck by turning the sleeve (13).
u Insert the bit shaft (14) into the chuck.
u Insert the chuck key (15) into each hole (16) in the side of
the chuck and turn until tight.
Residual risks.
Additional residual risks may arise when using the tool which
may not be included in the enclosed safety warnings. These
risks can arise from misuse, prolonged use etc.
Even with the application of the relevant safety regulations
and the implementation of safety devices, certain residual
risks can not be avoided. These include:
u Injuries caused by touching any rotating/moving
parts.
u Injuries caused when changing any parts, blades or
accessories.
u Injuries caused by prolonged use of a tool. When
using any tool for prolonged periods ensure you take
regular breaks.
u Impairment of hearing.
u Health hazards caused by breathing dust developed
when using your tool (example:- working with wood,
especially oak, beech and MDF.)
Use
Warning! Let the tool work at its own pace. Do not overload.
Warning! Before drilling into walls, oors or ceilings, check for
the location of wiring and pipes.
Selectingtheoperatingmode(g.E)
The tool can be used in three operating modes. Rotate the
drilling mode selector (5) towards the required position, as
indicated by the symbols.
Drilling
u For drilling in steel, wood and plastics, and for screwdriving
set the operating mode selector (5) to the
r
position.
u When screwdriving, start at a low speed. When removing
screws, the speed is automatically reduced.
Hammer drilling
u For hammer drilling in masonry and concrete, set the
operating mode selector (5) to the
s
position
u When hammering, the tool should not bounce and run
smoothly. If necessary, increase the speed.
Hammering
u For hammering with spindle lock, and for light chiselling
and chipping, set the operating mode selector (5) to the
q
position.
u Make sure the forward/reverse switch is in the forward
position.
u When changing from hammer drilling to chiselling, turn the
chisel to the desired position. If resistance is felt during
mode change, slightly turn the chisel to engage the
spindle lock.
Selecting the direction of rotation
For drilling, for tightening screws and for chiselling, use forward
(clockwise) rotation. For loosening screws or removing a
jammed drill bit, use reverse (counterclockwise) rotation.
u To select forward rotation, push the forward/reverse slider
(3) to the left.
u To select reverse rotation, push the forward/reverse slider
to the right.
Warning! Never change the direction of rotation while the
motor is running.
Settingthedrillingdepth(g.F)
u Slacken the side handle (7) by turning the grip
counterclockwise.
u Set the depth stop (8) to the desired position. The
maximum drilling depth is equal to the distance between
the tip of the drill bit and the front end of the depth stop.
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker KD976KA T3 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker KD976KA T3 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,94 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info