497050

Black Decker KD354 Manual

7
Zoom out
Zoom in
Previous page
1/12
Next page
7
FITTING THE DRILL BIT (KEYED CHUCKS)
Proceed as follows:
Disconnect the plug from the electricity supply.
Rotate the barrel
of the chuck until
the jaws are
sufficiently open.
Insert the drill bit
in the jaws of the
chuck. Insert the
chuck key with
the end of the chuck key in one of the three holes in the
body of the chuck and the head of the chuck key
engaged with the barrel of the chuck. Turn the chuck
key clockwise to tighten the jaws and securely grip the
drill bit. Remove the chuck key.
REMOVING THE CHUCK (KEYLESS CHUCKS)
Proceed as follows:
To remove the chuck,
open the jaws, hold
it firmly in one hand
and with a screwdriver
held in the other hand,
turn the set-screw in
the chuck clockwise
approximately one
turn, to loosen it.
Place an allen key in
the chuck and tighten the jaws. Give the allen key a
short powerful blow in an anti-clockwise direction with
a hammer to loosen the chuck on the spindle. Remove
the allen key. Use the screwdriver to turn the set-
screw clockwise until it totally disengages from the
spindle. Remove the chuck from the spindle by rotating
it anti-clockwise. To fasten the chuck, put it on the
thread and turn it clockwise until it stops. Put in the
screw and turn it anti-clockwise until absolutely firm.
REMOVING THE CHUCK (KEYED CHUCKS)
Proceed as follows:
To remove the chuck,
open the jaws of the
chuck with the chuck
key. Hold the chuck
firmly in one hand, and
with a screwdriver
turn the screw set in
the chuck clockwise
with the other hand
until it comes out.
Use only the correct chuck key. Place the chuck key
into the chuck, and hold the drill firmly in one hand with
the chuck pointing away from you. Rotate the chuck so
that the chuck key is just above the horizontal position
on the right hand side of the machine. Give the
crossbar end of the key a sharp downward blow with a
mallet or light hammer. The chuck should now be
sufficiently loose to be unscrewed by hand.
FITTING THE SIDE HANDLE
Proceed as follows:
Position the side
handle on the
body of your drill.
Rotate the handle
around the body
of your drill until it
is in the desired
position. Tighten the handle by turning clockwise.
SETTING THE ADJUSTABLE DEPTH STOP
Proceed as follows:
Fit the drill bit. Loosen the side handle.
Slide the depth stop
until the end of the
depth stop aligns
with the end of the
drill bit. Slide the
depth stop until the
distance between
the end of the depth
stop and the end of the drill bit is equal to the length of
the screw you will fit. Tighten the side handle.
PREPARING YOUR DRILL FOR OPERATION
Proceed as follows:
Fit the correct
accessory for the job.
Set the depth stop if
required. Set the
speed of your drill.
On two-speed drills,
set the two-speed switch to ‘1’ (low-speed) or ‘2’ (high-
speed), or set the variable speed control to the desired
speed. As a general rule, for large size drill bits use low
speeds and for smaller drill bits use high speeds.
Set the forward/
reverse switch to the
desired direction of
rotation. Never
change the setting of
the hammer switch,
ENGLISH
1
2
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker KD354 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker KD354 in the language / languages: English as an attachment in your email.

The manual is 0,41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Black Decker KD354

Black Decker KD354 User Manual - German - 44 pages

Black Decker KD354 User Manual - Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish - 64 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info