Manual Black Decker KD352 (page 23 of 64) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

601850

Zoom out

Zoom in

1/64

FITTING THE DRILL BIT (KEYED CHUCKS)

Proceed as follows:

Disconnect the plug from the electricity supply.

Rotate the barrel

of the chuck until

the jaws are

sufficiently open.

Insert the drill bit

in the jaws of the

chuck. Insert the

chuck key with

the end of the chuck key in one of the three holes in the

body of the chuck and the head of the chuck key

engaged with the barrel of the chuck. Turn the chuck

key clockwise to tighten the jaws and securely grip the

drill bit. Remove the chuck key.

REMOVING THE CHUCK (KEYLESS CHUCKS)

Proceed as follows:

To remove the chuck,

open the jaws, hold

it firmly in one hand

and with a screwdriver

held in the other hand,

turn the set-screw in

the chuck clockwise

approximately one

turn, to loosen it.

Place an allen key in

the chuck and tighten the jaws. Give the allen key a

short powerful blow in an anti-clockwise direction with

a hammer to loosen the chuck on the spindle. Remove

the allen key. Use the screwdriver to turn the set-

screw clockwise until it totally disengages from the

spindle. Remove the chuck from the spindle by rotating

it anti-clockwise. To fasten the chuck, put it on the

thread and turn it clockwise until it stops. Put in the

screw and turn it anti-clockwise until absolutely firm.

REMOVING THE CHUCK (KEYED CHUCKS)

Proceed as follows:

To remove the chuck,

open the jaws of the

chuck with the chuck

key. Hold the chuck

firmly in one hand, and

with a screwdriver

turn the screw set in

the chuck clockwise

with the other hand

until it comes out.

Use only the correct chuck key. Place the chuck key

into the chuck, and hold the drill firmly in one hand with

the chuck pointing away from you. Rotate the chuck so

that the chuck key is just above the horizontal position

on the right hand side of the machine. Give the

crossbar end of the key a sharp downward blow with a

mallet or light hammer. The chuck should now be

sufficiently loose to be unscrewed by hand.

FITTING THE SIDE HANDLE

Proceed as follows:

Position the side

handle on the

body of your drill.

Rotate the handle

around the body

of your drill until it

is in the desired

position. Tighten the handle by turning clockwise.

SETTING THE ADJUSTABLE DEPTH STOP

Proceed as follows:

Fit the drill bit. Loosen the side handle.

Slide the depth stop

until the end of the

depth stop aligns

with the end of the

drill bit. Slide the

depth stop until the

distance between

the end of the depth

stop and the end of the drill bit is equal to the length of

the screw you will fit. Tighten the side handle.

PREPARING YOUR DRILL FOR OPERATION

Proceed as follows:

Fit the correct

accessory for the job.

Set the depth stop if

required. Set the

speed of your drill.

On two-speed drills,

set the two-speed switch to ‘1’ (low-speed) or ‘2’ (high-

speed), or set the variable speed control to the desired

speed. As a general rule, for large size drill bits use low

speeds and for smaller drill bits use high speeds.

Set the forward/

reverse switch to the

desired direction of

rotation. Never

change the setting of

the hammer switch,

ENGLISH

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker KD352 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 2,14 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Black Decker KD352 Manual

Product: