577857

Black Decker KD1250K T1 Manual

6
Zoom out
Zoom in
Previous page
1/80
Next page
6
ENGLISH
(Original instructions)
Warning! The vibration emission value during actual use of
the power tool can differ from the declared value depending
on the ways in which the tool is used. The vibration level may
increase above the level stated.
When assessing vibration exposure to determine safety
measures required by 2002/44/EC to protect persons regularly
using power tools in employment, an estimation of vibration
exposure should consider, the actual conditions of use and the
way the tool is used, including taking account of all parts of the
operating cycle such as the times when the tool is switched off
and when it is running idle in addition to the trigger time.
Labels on tool
The following pictograms are shown on the tool:
:
Warning! To reduce the risk of injury, the user
must read the instruction manual.
Electrical safety
#
This tool is double insulated; therefore no earth
wire is required. Always check that the power
supply corresponds to the voltage on the rating
plate.
u If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised Black & Decker Service
Centre in order to avoid a hazard.
Features
This tool includes some or all of the following features.
1. On/Off switch
2. Speed selector dial
3. Drilling mode selector
4. Operating mode selector
5. Tool holder
6. Side handle
7. Depth stop
8. Grease cap
Assembly
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
Fitting the side handle (g. A)
u Turn the grip counterclockwise until you can slide the side
handle (6) onto the front of the tool as shown.
u Rotate the side handle into the desired position.
u Tighten the side handle by turning the grip clockwise.
Fitting and setting the depth stop (g. A)
u Slacken the knob (9).
u Insert the depth stop (7) into the mounting hole as shown.
u Set the depth stop (7) to the desired position. The maxi-
mum drilling depth is equal to the distance between the tip
of the drill bit and the front end of the depth stop.
u Tighten the knob (9).
Fitting an accessory (g. B - D)
u Clean and grease the shank (10) of the accessory.
u Pull back the sleeve (11) and insert the shank into the tool
holder (5).
u Push the accessory down and turn it slightly until it ts into
the slots.
u Pull on the accessory to check if it is properly locked. The
hammering function requires the accessory to be able to
move axially several centimetres when locked in the tool
holder.
u To remove the accessory, pull back the sleeve (11) and
pull out the accessory.
Keyed chuck (g. D)
u Open the chuck by turning the sleeve (12) anti-clockwise.
u Insert the bit shaft (13) into the chuck.
u Insert the chuck key (14) into each hole (15) in the side of
the chuck and turn clockwise until tight.
Use
Warning! Let the tool work at its own pace. Do not overload.
Warning! Before drilling into walls, oors or ceilings, check for
the location of wiring and pipes.
Warning! Do not apply chisels when the tool is in the drilling
mode.
Selecting the operating mode (g. F)
The tool can be used in three operating modes.
u To operate the drilling mode selector (3), rotate it towards
the required position, as indicated by the symbols.
u To operate the operating mode selector (4), push the
unlock button (16) and rotate the selector towards the
required position, as indicated by the symbols.
Drilling
u For drilling in steel, wood and plastics, and for screwdriv-
ing set the operating mode selector (4) to the
position
and the drilling mode selector (3) to the position.
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker KD1250K T1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker KD1250K T1 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 5,4 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Black Decker KD1250K T1

Black Decker KD1250K T1 User Manual - Polish - 12 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info