Manual Black Decker KC8404 (page 4 of 58) (English, German, Dutch, French, Italian, Portuguese, Spanish)

473003

Zoom out

Zoom in

1/58

ENGLISH

• If charging problems persist, take or send

the tool, energy pack and charger to an

authorised service centre.

• The energy pack should be recharged when it

fails to produce sufficient power on jobs which

were easily done previously. Do not continue to

use under these conditions. Follow the charging

procedure described above. You may also

charge a partially used pack whenever you wish.

1 hour charger only:

• The charger and energy pack can be left

connected indefinitely. The charger will keep the

energy pack fully charged.

Switch and forward/reverse lever

(Figs. C1 - 4)

To turn the drill on, squeeze the trigger switch.

To turn the drill off, release the trigger switch

(Fig. C1).

The forward/reverse lever is a three position

lever located over the trigger switch in the

housing.

• During charging, changing accessories

or storage, move the lever to the “Off”

position in the middle (Fig. C2).

• Slide it to the right to drill holes or

drive screws (Fig. C3).

• To remove screws or back out jammed

drill bits, move the lever fully to the left

(Fig. C4).

Two speed selector (Fig. D)

Your drill has a two speed mechanical gear

selector at the top of the housing. In order to

change the speed setting, allow the chuck to

rotate slowly by pressing gently on the

trigger switch.

To select the low speed setting, slide the

selector switch towards the front end of the

drill. The number 1 will appear on the

selector. This will produce a speed ideal for

screwdriving (Fig. D).

To select the high speed setting, slide the

selector switch towards the back end.

The number 2 will appear on the selector.

This will produce a speed ideal for drilling

and hammer drilling.

Warning! Do not change gear while the unit

is running.

Torque control (except KC8402C)

Your drill/driver is equipped with a torque

control mechanism to enable you to do

repetitive screwdriving.

• When screwing in the first screw,

determine the correct torque setting

which will result in the screw being flush

with the surface of the workpiece.

• By keeping the same torque setting,

all following screws will also be flush with

the workpiece, due to the torque

mechanism which disengages the

power of the motor at the moment the

screw is flush.

• This mechanism prevents damage to

the screwhead and the workpiece

(e.g. screws are not driven in too far).

Combination percussion action and

torque adjustment collar (KC8482C,

KC9682C & KC1282C)

These units are equipped with a combination

percussion action and torque adjustment

collar. To select for percussion action rotate

the collar until the hammer symbol is in line

with the indicator on the top of the drill

housing. To select the correct action for

non-masonry drilling tasks rotate the collar

until the drill bit symbol is in line with the

indicator on the top of the drill housing.

For screwdriving, these units are equipped

with 5 position collars, allowing adjustment

of the torque to suit the size of the screw

and the material involved. Before starting

work, adjust the torque in the following way.

Set the collar in position 1 and begin

screwdriving (low torque). If the machine

clutch ratchets too early, adjust the collar to

increase the torque as required.

Maximum recommended capacities

8.4V 9.6V 12V

Steel 10mm 10mm 10mm

Wood 15mm 20mm 25mm

Masonry (combi only) 10mm 10mm 12mm

Chucks (Figs. F1 - 3)

Keyless chuck

To insert a drill bit or other accessory,

follow the steps listed below:

• Switch the control lever to the

“Off” position.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker KC8404 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 0,4 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Black Decker KC8404 Manual

Product: