472996
29
Zoom out
Zoom in
Previous page
1/72
Next page
29
ENGLISH
The torque adjustment collar has 5 positions and
provides adjustment of the torque necessary to seat
screws of a given size in a particular material.
Proceed as follows:
Set the torque
adjustment collar to
position ‘1’.
Fit and tighten the first
screw. If the clutch of
your drill starts to slip
before the screw is
correctly seated, rotate
the torque adjustment collar, as necessary, until the
clutch slips when the head of the screw is flush with
the surface of the material. Use this torque setting
when fitting the remaining screws.
FAST CHARGER AND DETACHABLE BATTERY PACK
Your drill has a fast charger and detachable battery
pack. To increase the availability of your drill you can
purchase an additional battery pack.
CHARGING YOUR CORDLESS DRILL
Important! The battery pack in your drill is not charged
when supplied as new. A new battery, or one which
has not been used for an extended period, achieves full
performance only after approximately 5 charging and
discharging cycles. Before attempting to charge your
drill, read all the safety instructions.
To charge your drill, proceed as follows:
Put the forward/reverse switch in the centre (lock-off)
position. Remove all accessories from the chuck.
To remove the battery
pack, depress the two
release buttons and
withdraw the battery
pack. Plug the charger
into a standard 220/240V
socket. Place the battery
pack in the charger.
While charging, your
battery pack may hum
and become warm to the
touch; this is normal.
3-5 hour charger
After normal usage your power pack should be fully
charged in 3 hours. If your power pack is run-down
completely it may take up to 8 hours to become fully
charged.
Your power pack was sent from the factory in an
uncharged condition; before attempting to use it, it
must be charged for at least 6 hours.
To prolong your power packs’ life, avoid leaving it on
charge for more than 8 hours. Although overcharging is
not a safety concern, it can reduce the overall life of
your power pack.
1 hour fast charger
Place the battery pack in the charger. Leave it until
the red light goes out and the green light shows. The
battery pack is then ready to use.
If the battery has been used recently and is too hot, the
red charge light still comes on but the charger will not
charge until the battery temperature reduces to below
45˚C. Once below 45˚C you must re-insert the pack to
actually start charging.
The battery charger recognises the charged condition
and switches a fully charged battery immediately to
trickle charging. By this means, the battery can remain
indefinately in the charger without risk to the battery life.
Both chargers
Disconnect the plug from the electricity supply before
making or breaking connections to the battery pack.
For the longest battery life, charge the battery pack in
an air temperature of approximately 24°C/75°F. Do not
charge the battery pack if the air temperature is below
5°C/41°F or above 35°C/95°F.
The charger can remain in the electrical socket
indefinitely without adverse effect. If the battery pack
does not charge correctly, check the supply at the
electrical socket with a lamp or other appliance.
If the electricity supply is satisfactory and your drill is
still not charging, take or send your drill and charger to
your local Black & Decker authorised repair agent.
FITTING THE DRILL OR SCREWDRIVER BIT
Make sure the forward/reverse switch is in the centre
(lock-off) position.
While holding the rear
section of the chuck,
rotate the front section
until the jaws of the
chuck are sufficiently
open. Insert the drill bit
in the jaws of the chuck.
Hold the rear section of the chuck while tightening the
front section. Tighten the two sections firmly in
opposite directions to securely grip the drill bit.
3
2
1
4
5
29


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker KC7251 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker KC7251 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 3,13 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info