25066
6
Zoom out
Zoom in
Previous page
1/12
Next page
6
Before replacing the top cover of the mains plug ensure
that the cable restraint (3) is holding the outer sheath of
the cable firmly and that the leads are correctly fixed at
the terminal screws.
If the plug has a fuse cover, make sure that the fuse cover
is fitted. Do not use the plug if the fuse cover is missing
or damaged.
Never use a light socket.
OVERVIEW (fig. A)
Motor unit
1. Variable speed switch
2. Forward/reverse slider
3. Head release button
4. Bit holder
5. Battery
6. Battery release buttons
Drill/screwdriver head
7. Torque adjustment collar
8. Chuck
Jigsaw head
9. Lock-off button
10. Saw shoe
Sander head
11. Sanding base
Charger
12. Charger
13. Charging indicator
14. End of charge indicator
Assembly
Warning! Before assembly, remove the battery from the tool.
Fitting and removing the battery (fig. B)
KC2000
To fit the battery (5), line it up with the receptacle on the
tool. Slide the battery into the receptacle and push until
the battery snaps into place.
To remove the battery, push the two release buttons (6)
simultaneously while at the same time pulling the battery
out of the receptacle.
KC2002
To fit the battery (5), line it up with the receptacle on the
tool. Slide the battery into the receptacle and push until
the battery snaps into place.
To remove the battery, push the release button (10) while
at the same time pulling the battery out of the receptacle.
Fitting and removing tool heads (fig. C)
The different tool heads can be easily exchanged.
Lock the tool by setting the forward/reverse slider (2) to
the centre position.
To remove a tool head, depress the head release button (3)
and take the head off the tool.
To fit a tool head, line it up with the tool as shown and
push it onto the tool until it snaps into place.
Fitting and removing a drill bit or screwdriver bit
(fig. A & D)
The drill/screwdriver head is fitted with a keyless chuck to
allow for an easy exchange of bits.
Lock the tool by setting the forward/reverse slider (2) to
the centre position (fig. A).
Open the chuck by turning the front part (15) with one
hand while holding the rear part (16) with the other (fig. D).
Insert the bit shaft (17) into the chuck.
Firmly tighten the chuck by turning the front part (15) with
one hand while holding the rear part (16) with the other.
This tool is supplied with a double-ended screwdriver bit in
the bit holder (4) (fig. A).
To remove the screwdriver bit from the bit holder, lift the
bit from the recess.
To store the screwdriver bit, firmly push it into the holder.
Fitting and removing a saw blade (fig. F & G)
Lock the tool by setting the forward/reverse slider (2) to
the centre position (fig. F).
To fit a saw blade, lift the lever (18) and hold it in this
position (fig. G).
Insert the saw blade into the holder as shown. Make sure
that the teeth are pointing to the front.
Release the lever.
To remove the saw blade, lift the lever (18) and pull the
saw blade from the holder.
Fitting and removing sanding sheets (fig. F & I)
The sanding head uses pre-cut sanding sheets.
Lock the tool by setting the forward/reverse slider (2) to
the centre position (fig. F).
Before fitting a new sheet, remove the two additional
diamond tips (20) (fig. I).
To fit a sanding sheet, line it up with the sanding base as
shown.
Press the sheet firmly and evenly onto the sanding base,
making sure that the holes in the sheet coincide with the
holes in the base.
To remove the sheet, pull it off the sanding pad.
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker KC2000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker KC2000 in the language / languages: English as an attachment in your email.

The manual is 0,47 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Black Decker KC2000

Black Decker KC2000 User Manual - English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish - 88 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info