382791

Black Decker kc 2002 fm Manual

8
Zoom out
Zoom in
Previous page
1/88
Next page
8
ENGLISH
When sawing wooden workpieces, it is not necessary to drill a
pilot hole:
◆ Mark the desired starting point.
◆ Tilt the tool forward and place the rounded front edge of
the saw shoe on the workpiece.
◆ Switch the tool on and slowly feed the saw blade into the
workpiece at the desired starting point.
When cutting sheet metal:
◆ Clamp a piece of plywood or soft wood to the back of the
workpiece and saw through the combination in order to
obtain a clear cut.
◆ Do not force the saw blade into the workpiece. Note that
cutting sheet metal will normally take more time than
sawing thicker wooden workpieces.
◆ Spread a thin film of oil along the cutting line before sawing.
◆ To cut, switch the tool on and move it down until the saw
blade is exactly over the point of entry.
Lower the rear of the shoe towards the workpiece,
maintaining a firm pivoting pressure on the saw shoe.
With the shoe flat on the workpiece, feed the blade into
the workpiece.
When cutting laminates:
◆ Cut thin laminates with the back surface facing up,
as splintering is most likely to occur on the side of the
workpiece facing the saw shoe.
◆ For clean cuts, clamp a piece of plywood or hardboard to
both sides of the laminate and cut through the resulting
sandwich.
Sanding
◆ Do not exert too much pressure on the tool.
◆ Regularly check the condition of the sanding sheet.
Replace when necessary.
◆ When sanding new layers of paint before applying
another layer, use extra fine grit.
◆ On very uneven surfaces, or when removing layers of
paint, start with a coarse grit. On other surfaces, start
with a medium grit. In both cases, gradually change to a
fine grit for a smooth finish.
◆ Consult your retailer for more information on available
accessories for sanding, polishing, stripping and scrubbing.
Maintenance
Your Black & Decker tool has been designed to operate over a
long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
Your charger does not require any maintenance apart from
regular cleaning.
Warning! Before performing any maintenance on the tool,
remove the battery from the tool. Unplug the charger before
cleaning it.
◆ Regularly clean the ventilation slots in your tool and
charger using a soft brush or dry cloth.
◆ Regularly clean the motor housing using a damp cloth.
Do not use any abrasive or solvent-based cleaner.
◆ Regularly open the chuck and tap it to remove any dust
from the interior.
◆ Regularly apply a drop of light machine oil to the guide
roller (22) of the jigsaw head (fig. K).
Protecting the environment
Tools
Black & Decker provides a facility for recycling
Black & Decker products and rechargeable batteries
once they have reached the end of their working life.
This service is provided free of charge. To take
advantage of this service please return your product
to any authorised repair agent who will collect them
on our behalf.
Batteries
Cd
Black & Decker batteries can be recharged many
times. At the end of their useful life, discard
batteries with due care for our environment:
◆ Run the battery down completely, then remove it from the
tool.
◆ NiCd and NiMH batteries are recyclable. Take them to
any authorised repair agent or a local recycling station.
You can check the location of your nearest authorised repair
agent by contacting your local Black & Decker office at the
address indicated in this manual. Alternatively, a list of
authorised Black & Decker repair agents and full details of our
after-sales service and contacts are available on the Internet
at: www.2helpU.com.
Technical data
KC2000 KC2002
Voltage V
DC
12 14.4
Battery cat. no. A9275 $
Drill/screwdriver:
No-load speed min
-1
0 - 700 0 - $
Max. torque Nm 6.2 $
Chuck capacity mm 10 10
Max. drilling capacity in steel/wood mm 10/25 10/25
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker kc 2002 fm at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker kc 2002 fm in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,83 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info