383577

Black Decker kc 2000 fm Manual

6
Zoom out
Zoom in
Previous page
1/88
Next page
6
ENGLISH
Assembly
Warning! Before assembly, remove the battery from the tool.
Fitting and removing the battery (fig. B)
KC2000
◆ To fit the battery (5), line it up with the receptacle on the
tool. Slide the battery into the receptacle and push until
the battery snaps into place.
◆ To remove the battery, push the two release buttons (6)
simultaneously while at the same time pulling the battery
out of the receptacle.
KC2002
◆ To fit the battery (5), line it up with the receptacle on the
tool. Slide the battery into the receptacle and push until
the battery snaps into place.
◆ To remove the battery, push the release button (10) while
at the same time pulling the battery out of the receptacle.
Fitting and removing tool heads (fig. C)
The different tool heads can be easily exchanged.
◆ Lock the tool by setting the forward/reverse slider (2) to
the centre position.
◆ To remove a tool head, depress the head release button (3)
and take the head off the tool.
◆ To fit a tool head, line it up with the tool as shown and
push it onto the tool until it snaps into place.
Fitting and removing a drill bit or screwdriver bit
(fig. A & D)
The drill/screwdriver head is fitted with a keyless chuck to
allow for an easy exchange of bits.
◆ Lock the tool by setting the forward/reverse slider (2) to
the centre position (fig. A).
◆ Open the chuck by turning the front part (15) with one
hand while holding the rear part (16) with the other (fig. D).
◆ Insert the bit shaft (17) into the chuck.
◆ Firmly tighten the chuck by turning the front part (15) with
one hand while holding the rear part (16) with the other.
This tool is supplied with a double-ended screwdriver bit in
the bit holder (4) (fig. A).
◆ To remove the screwdriver bit from the bit holder, lift the
bit from the recess.
◆ To store the screwdriver bit, firmly push it into the holder.
Fitting and removing a saw blade (fig. F & G)
◆ Lock the tool by setting the forward/reverse slider (2) to
the centre position (fig. F).
◆ To fit a saw blade, lift the lever (18) and hold it in this
position (fig. G).
◆ Insert the saw blade into the holder as shown. Make sure
that the teeth are pointing to the front.
◆ Release the lever.
◆ To remove the saw blade, lift the lever (18) and pull the
saw blade from the holder.
Fitting and removing sanding sheets (fig. F & I)
The sanding head uses pre-cut sanding sheets.
◆ Lock the tool by setting the forward/reverse slider (2) to
the centre position (fig. F).
◆ Before fitting a new sheet, remove the two additional
diamond tips (20) (fig. I).
◆ To fit a sanding sheet, line it up with the sanding base as
shown.
◆ Press the sheet firmly and evenly onto the sanding base,
making sure that the holes in the sheet coincide with the
holes in the base.
◆ To remove the sheet, pull it off the sanding pad.
Warning! Never use the sanding head without a sanding
sheet or accessory in place.
Replacing the diamond sanding tip (fig. F & J)
Sanding sheets are supplied with two replacement diamond
tips. The diamond tip can be reversed when worn. When both
sides are worn, replace the diamond tip.
◆ Lock the tool by setting the forward/reverse slider (2) to
the centre position (fig. F).
◆ To reverse the tip, remove it, turn it 180° and press it back
onto the base as shown (fig. J).
◆ To replace the tip, pull the old tip off the base and press a
new one onto the base.
Warning! When removing the tip from the pad, be careful not
to pull the pad off the sanding base.
Use
Warning! Let the tool work at its own pace. Do not overload.
Charging the battery (fig. A)
The battery needs to be charged before first use and whenever
it fails to produce sufficient power on jobs that were easily
done before. A new battery, or a battery that has not been
used for an extended period of time, achieves full performance
only after approx. 5 charging and discharging cycles. The battery
may become warm while charging; this is normal and does not
indicate a problem. After normal use, a charging time of
60 minutes will provide sufficient power for most applications.
However, further charging for up to 90 minutes could
significantly increase the use time, depending on the battery
and charging conditions.
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker kc 2000 fm at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker kc 2000 fm in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,83 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info