578034
8
Zoom out
Zoom in
Previous page
1/16
Next page
8
the operating cycle such as the times when the tool is
switched off and when it is running idle in addition to the
trigger time.
Labels on tool
The following pictograms are shown on the tool:
:
Warning! To reduce the risk of injury, the user must
read the instruction manual.
Fit the dustbag or dust cassette before using the tool
on wooden workpieces.
Remove the dustbag or cassette and t the deector
before using the tool on workpieces containing
metal.
Electrical safety
#
This tool is double insulated; therefore no earth wire
is required. Always check that the power supply
corresponds to the voltage on the rating plate.
u If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised Black & Decker Service
Centre in order to avoid a hazard.
Features
Your tool has some or all of the following features:
1. On/off switch
2. Variable speed control knob
3. Lock-on button
4. Secondary handle
5. Belt tensioning lever
6. Belt tracking knob
7. Straight arm
Fig. A
8. Narrow arm
9. Cranked arm
Fig. D
10. Dust cassette
11. Deector
Assembly
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
Fitting and removing sanding arms (g. A & B)
The tool is supplied with the following sanding arms:
u Straight arm (7), sanding width 13 mm
u Narrow arm (8), sanding width 6 mm, for intricate work
u Cranked arm (9) for grooving and sanding in the centre of
workpieces and for reaching conned areas
Before rst use, you must t the sanding arm to the tool.
Fitting
u Make sure that the belt tensioning lever (5) is in the
position shown.
u Loosen and remove the belt tracking knob (6).
u Remove the tape retaining the spring (12) (if present).
u Check that the spring (12) is located in its mounting hole.
u Position the arm as shown.
u Fit the belt tracking knob (6) and tighten it until the arm (7)
is aligned with the tool.
Removing
u Remove the sanding belt (13) (if present) as described below.
u Loosen and remove the belt tracking knob (6).
u Remove the arm.
Warning! Be careful not to lose the spring (12).
Fitting and removing sanding belts (g. B)
Warning! The spring must be tted. Be careful not to lose the
spring (12).
Fitting
u Move the belt tensioning lever (5) to the front position (A).
u Make sure that the arrows on the inside of the sanding
belt (13) face the same direction as the arrows (14) on the
housing.
u Place the sanding belt (13) over the front pulley (15) and
the rear pulley (16), sliding it through the slot in the
housing.
u Move the belt tensioning lever (5) to the rear position (B).
u Adjust the belt tracking as described below.
Removing
u Move the belt tensioning lever (5) to the front position (A).
u Slide the sanding belt (13) off the pulleys.
Adjusting the sanding belt tracking (g. C)
u Switch the tool on.
u Turn the belt tracking knob (6) as required until the
sanding belt (13) runs straight along the length of the arm.
Fitting and removing the dust cassette (g. D & F)
Warning! Always remove the dust cassette and t the
deector when using the tool on metal workpieces.
u Fit the dust cassette (10) over the dust extraction outlet.
u Slide the item onto the tool and make sure that it is
securely located.
u To remove the dust cassette, pull it to the rear and off the
outlet.
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker KA902E T1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker KA902E T1 in the language / languages: English as an attachment in your email.

The manual is 0,66 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Black Decker KA902E T1

Black Decker KA902E T1 User Manual - English, German, Dutch, Danish, French, Italian, Portuguese, Swedish - 84 pages

Black Decker KA902E T1 User Manual - Turkish - 12 pages

Black Decker KA902E T1 User Manual - Spanish, Norwegian, Finnish - 84 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info