578033
8
Zoom out
Zoom in
Previous page
1/16
Next page
8
If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised Black & Decker Service
Centre in order to avoid a hazard.
Features
Your tool has some or all of the following features:
1. Variable speed control knob
2. On/off switch
3. Lock-on button
4. Secondary handle
5. Belt tensioning lever
6. Belt tracking knob
7. Straight arm
Fig. A
9. Narrow arm (Where supplied)
10. Cranked arm (Where supplied)
Fig. D
13. Dustbag (Where supplied)
14. Dust cassette
15. Deflector
Assembly
Warning! Before assembly, make sure that the tool is switched
off and unplugged.
Fitting and removing sanding arms (fig. A)
Before first use, you must fit a sanding arm to the tool. Your
tool is supplied with the following:
A straight arm (7, sanding width 13 mm).
a narrow arm (9, sanding width 6 mm) for intricate work
a cranked arm (10) for grooving and sanding in the centre
of workpieces and for reaching confined areas
These parts are also available as an accessory from your
Black & Decker dealer, (not available in Australia and New
Zealand).
Fitting
Make sure that the belt tensioning lever (5) is in the position
shown.
Loosen and remove the belt tracking knob (6).
Remove the tape retaining the spring (8) (if present).
Check that the spring (8) is located in its mounting hole.
Position the arm (7, 9 or 10) as shown.
Fit the belt tracking knob (6) and tighten it until the arm (7)
is aligned with the tool.
Removing
Remove the sanding belt (12) (if present) as described
below.
Loosen and remove the belt tracking knob (6).
Remove the arm (7, 9 or 10).
Warning! Be careful not to lose the spring (8).
Fitting and removing sanding belts (fig. B)
Warning! The spring must be fitted. Be careful not to lose the
spring (8).
Fitting
Move the belt tensioning lever (5) to the front position (A).
.Make sure that the arrows on the inside of the sanding belt
(12) face the same direction as the arrows (17) on the
housing.
Place the sanding belt (12) over the front pulley (11) and
the rear pulley (16), sliding it through the slot in the housing.
Move the belt tensioning lever (5) to the rear position (B).
Adjust the belt tracking as described below.
Removing
Move the belt tensioning lever (5) to the front position (A).
Slide the sanding belt (12) off the pulleys.
Adjusting the sanding belt tracking (fig. C)
Switch the tool on.
Turn the belt tracking knob (6) as required until the sanding
belt runs straight along the length of the arm.
Fitting and removing the dust cassette or the dust bag
(fig. D, E and F)
Warning! Always remove the dustbag or dust cassette and fit
the deflector when using the tool on metal workpieces.
Fitting
Fit the dust cassette (14) or the dust bag (13) over the dust
extraction outlet.
Slide the item (13 or 14) onto the tool and make sure that it
is securely located.
Removing
To remove the dust cassette (14), or the dust bag (13), pull
the item (13 or 14) to the rear and off the outlet.
Fitting and removing the deflector (fig. D and E)
Warning! The deflector must be used when sanding metal
workpieces.
Fitting
Fit the deflector (15) over the dust extraction outlet.
Slide the deflector (15) on to the tool and make sure that it
is securely located.
Removing
To remove the deflector (15), pull the deflector to the rear
and off the outlet.
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker KA900E T1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker KA900E T1 in the language / languages: English as an attachment in your email.

The manual is 1,17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Black Decker KA900E T1

Black Decker KA900E T1 User Manual - English, German, Dutch, Danish, French, Italian - 92 pages

Black Decker KA900E T1 User Manual - Polish - 16 pages

Black Decker KA900E T1 User Manual - Portuguese, Swedish - 92 pages

Black Decker KA900E T1 User Manual - Turkish - 16 pages

Black Decker KA900E T1 User Manual - Spanish, Norwegian, Finnish - 92 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info