21829
4
Zoom out
Zoom in
Previous page
1/8
Next page
4
Electrical safety
This tool is double insulated; therefore no earth wire
is required. Always check that the power supply
corresponds to the voltage on the rating plate.
Additional safety instructions for Australia and
New Zealand
This appliance is not intended for use by young or infirm
persons without supervision. Children must be supervised
to ensure they do not play with the appliance.
If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised Black & Decker Service
Centre in order to avoid a hazard.
Additional safety instructions for sanders
Always wear a dust mask whenever sanding.
Thoroughly remove all dust after sanding.
Take special care when sanding paint which is possibly
lead based or when sanding some woods and metal
which may produce toxic dust:
- Wear a dust mask specifically designed for protection
against lead paint dust and fumes and ensure that persons
within or entering the work area are also protected.
- Do not let children or pregnant women enter the work
area.
- Do not eat, drink or smoke in the work area.
- Dispose of dust particles and any other debris safely.
Features
1. On/off switch
2. Gel comfort grip
3. Dust extraction outlet
4. Dust bag
5. Sanding base
6. Paper clamp lever
7. Paper punch
Assembly
Warning! Make sure that the tool is switched off and
unplugged.
Fitting sanding sheets (fig. A - C)
Warning! Never use the tool without a sanding sheet or
accessory in place.
Fitting sanding sheets with nylon loops (fig. A)
Make sure that the tool is switched off and unplugged.
Press the sheet firmly and evenly onto the sanding base
(5), making sure that the holes in the sheet line up with
the holes in the base.
Fitting regular sanding sheets (fig. B)
Make sure that the tool is switched off and unplugged.
Soften the sanding sheet by rubbing its non-abrasive side
over the edge of a worktop.
Press the paper clamp levers (6) upwards to release them
from the retaining grooves and open the paper clamps by
pressing them down.
Place the sheet onto the sanding base.
Insert the edge of the sanding sheet into the front paper
clamp as shown.
Press the front paper clamp lever (6) downwards and
locate it in the retaining groove.
While keeping a slight tension on the sheet, insert the
rear edge of the sheet into the rear paper clamp.
Press the rear paper clamp lever (6) downwards and
locate it in the retaining groove.
Punching sanding sheets (fig. C)
The paper punch (7) is used for punching dust extraction holes
in sanding sheets without pre-punched holes. For optimum
convenience the paper punch can be fitted to a workbench
using the screw holes (8).
Fit a sanding sheet.
Hold the tool in position right above the paper punch (7).
Press the tool with the sanding base (5) down into the
paper punch.
Take the tool off the paper punch and check whether the
holes in the sanding sheet have been fully pierced.
Fitting and removing the dustbag (fig. D)
Fit the dustbag (4) over the dust extraction outlet (3).
To remove the dustbag, pull the dustbag to the rear and
off the outlet.
Use
Switching on and off
To switch the tool on, press the I part of the on/off switch
(1).
To switch the tool off, press the O part of the on/off switch.
Emptying the dustbag
The dustbag should be emptied every 10 minutes.
Shake the dustbag to empty the contents.
Hints for optimum use
(fig. E)
Hold the tool as shown.
Do not exert too much pressure on the tool.
Regularly check the condition of the sanding sheet.
Replace when necessary.
Always sand with the grain of the wood.
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker KA170GT at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker KA170GT in the language / languages: English as an attachment in your email.

The manual is 0,61 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Black Decker KA170GT

Black Decker KA170GT User Manual - English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Finnish - 52 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info