Manual Black Decker KA150 (page 22 of 64) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Spanish, Norwegian, Finnish)

21667

Zoom out

Zoom in

1/64

ENGLISH

PREPARING YOUR MOUSE

To prepare your Mouse, proceed as follows:

Disconnect the plug from the electricity supply.

Fit the appropriate abrasive or accessory to the base of

the tool and connect the dust extraction outlet to a

vacuum cleaner.

USING YOUR MOUSE WITH THE POINTED BASE

Your Mouse is equipped

with a teardrop base

which allows you to use

it on large flat surfaces,

as well as difficult and

confined areas.

FITTING THE ABRASIVE

Your Mouse uses pre-cut nylon backed sheets of

abrasive of a specific size.

To fit the abrasive proceed as follows:

Disconnect the plug from the electricity supply.

Press the nylon loop side

of the abrasive against

the hooks on the base.

Align the holes in the

abrasive (where fitted)

with the dust extraction

holes in the base of the

Mouse. Ensure the

abrasive evenly overlaps the base. Never use your

Mouse without an abrasive or accessory. The abrasive

supplied with your tool has two replacement tips

supplied. In addition, the abrasive is designed to allow

you to interchange and or rotate the diamond tip.

To rotate the diamond tip,

remove the tip, rotate it

through 180˚ and press it

back on the hook base as

shown. Note: Remove the

two replacement tips

from the abrasive before

using the Mouse, these

can be used later when the original diamond tip wears.

FITTING THE FINGER ATTACHMENT BASE (KA150K)

Disconnect the plug from

the electricity supply.

First remove the abrasive

and then remove the 2

small screws in the

Mouse base using the

screwdriver provided.

Looking from the bottom

of the Mouse rotate the

base in a clockwise

direction whilst holding

the Mouse in one hand

and the base in the other.

The base can be lifted off

and removed.

Take the finger

attachment base and

locate the three legs into

the location holes in the

Mouse. Turn the finger

attachment base anti

clockwise as shown to attach the base. The finger

should point directly from the front of the Mouse.

Replace the small screws into the base of the finger

attachment base. Note: The screws must be placed

back into the base for the unit to work properly.

DUST EXTRACTION

Your Mouse has an adaptor to connect it to a vacuum

cleaner when sanding wood.

To connect to the vacuum cleaner, proceed as follows:

Disconnect the plug from the electricity supply.

Insert the adaptor into

the rear outlet of the

Mouse and connect the

hose of a vacuum

cleaner.

OPERATING YOUR MOUSE

To switch your Mouse

on, press the on/off

switch on the side

marked “I”.

To switch your Mouse

off, press the on/off

switch on the side “0”.

Before plugging your

Mouse in to the electricity supply, make sure it is

switched off on your Mouse.

HANDY HINTS

• Do not apply excessive pressure when you use

your Mouse.

• Replace the abrasive when it is worn.

• Use high grit abrasive for a fine finish.

KA150K ML p19-33 21-09-2000, 13:5522

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker KA150 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 2,72 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Black Decker KA150 Manual

Product: