390043

Black Decker ka 400 Manual

6
Zoom out
Zoom in
Previous page
1/76
Next page
6
ENGLISH
Labels on tools
The following pictograms are shown on the tool:
Electrical safety
If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised Black & Decker Service
Centre in order to avoid a hazard.
Features
1. On/off switch
2. Dustbag
3. Dust extraction outlet
4. Sanding base
5. Paper clamp lever
Assembly
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
Fitting sanding sheets (fig. A & B)
Warning! Never use the tool without a sanding sheet or
accessory in place.
Fitting sanding sheets with nylon loops (fig. A)
Warning! Make sure that the tool is switched off and
unplugged.
Press the sheet firmly and evenly onto the sanding
base (4), making sure that the holes in the sheet line up
with the holes in the base.
Fitting regular sanding sheets (fig. B)
Warning! Make sure that the tool is switched off and
unplugged.
Soften the sanding sheet by rubbing its non-abrasive
side over the edge of a worktop.
Press the paper clamp levers (5) upwards to release
them from the retaining grooves and open the paper
clamps (5) by pressing them down.
Place the sheet onto the sanding base (4).
Insert the edge of the sanding sheet into the front paper
clamp (5) as shown.
Press the front paper clamp lever (5) downwards and
locate it in the retaining groove.
While keeping a slight tension on the sheet, insert the
rear edge of the sheet into the rear paper clamp (5).
Press the rear paper clamp lever (5) downwards and
locate it in the retaining groove.
Louvre attachment (fig. C) (KA400L only)
With this attachment you can work in crevices and use the
sanding base on both sides.
Locate the front of the louvre attachment (7) onto the
sanding base (4).
Secure it in position with the four screws supplied.
Place a 1/2 sheet to the underside of the louvre base.
Part of it will fold over the front part of the base.
To remove the louvre attachment (7), reverse the
procedure.
Fitting and removing the dustbag (fig. D)
Fit the dustbag (2) over the dust extraction outlet (3).
Slide the dustbag (2) onto the tool and make sure that it
is securely located.
To remove the dustbag (2), pull it to the rear and off the
outlet.
Residual risks
Additional residual risks may arise when using the tool which
may not be included in the enclosed safety warnings. These
risks can arise from misuse, prolonged use etc.
Even with the application of the relevant safety regulations
and the implementation of safety devices, certain residual
risks cannot be avoided. These include:
Injuries caused by touching any rotating/moving parts.
Injuries caused when changing any parts, blades or
accessories.
Injuries caused by prolonged use of a tool. When using
any tool for prolonged periods make sure you take
regular breaks.
Impairment of hearing.
Health hazards caused by breathing dust developed
when using your tool (example:- working with wood,
especially oak, beech and MDF).
Use
Warning! Let the tool work at its own pace. Do not overload.
Switching on and off (fig. E)
To switch the tool on, press the part of the on/off switch
(1) marked 'I'.
To switch the tool off, press the part of the on/off switch
(1) marked '0'.
Emptying the dustbag
The dustbag (2) should be emptied every 10 minutes.
Shake the dustbag (2) to empty the contents
Warning! To reduce the risk of injury, the user must
read the instruction manual.
This tool is double insulated; therefore no earth
wire is required. Always check that the power
supply corresponds to the voltage on the rating
plate.
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker ka 400 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker ka 400 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Finnish as an attachment in your email.

The manual is 2,26 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info