Manual Black Decker ka 320 eka (page 7 of 72) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Finnish)

389517

Zoom out

Zoom in

1/72

ENGLISH

Labels on tool

The following pictograms are shown on the tool:

Warning! To reduce the risk of injury, the user must

read the instruction manual.

Electrical safety

This tool is double insulated; therefore no earth wire

is required. Always check that the power supply

corresponds to the voltage on the rating plate.

u If the supply cord is damaged, it must be replaced by the

manufacturer or an authorised Black & Decker Service

Centre in order to avoid a hazard.

Using an extension cable

u Always use an approved extension cable suitable for the

power input of this tool (see technical data). Before use,

inspect the extension cable for signs of damage, wear and

ageing. Replace the extension cable if damaged or

defective. When using a cable reel, always unwind the

cable completely. Use of an extension cable not suitable

for the power input of the tool or which is damaged or

defective may result in a risk of re and electric shock.

Features

This tool includes some or all of the following features.

1. On/off switch

2. Dust extraction outlet

3. Sanding base

4. Paper clamp lever

5. Variable speed control knob

Assembly

Warning! Before assembly, make sure that the tool is

switched off and unplugged.

Fittingsandingsheets(g.A&B1-B3)

Warning! Never use the tool without a sanding sheet or

accessory in place.

Fittingsandingsheetswithnylonloops(g.A)

u Make sure that the tool is switched off and unplugged.

u Press the sheet rmly and evenly onto the sanding base

(3), making sure that the holes in the sheet line up with the

holes in the base.

Fittingregularsandingsheets(g.B1-B3)

u Make sure that the tool is switched off and unplugged.

u Soften the sanding sheet by rubbing its non-abrasive side

over the edge of a worktop.

u Press the paper clamp levers (4) upwards to release them

from the retaining grooves and open the paper clamps by

pressing them down (g. B1).

u Place the sheet onto the sanding base (3), making sure

that the holes in the sheet line up with the holes in the

base (g. B2).

u Insert the edge of the sanding sheet into the front paper

clamp as shown (g. B3).

u Press the front paper clamp lever (4) downwards and

locate it in the retaining groove.

u While keeping a slight tension on the sheet, insert the rear

edge of the sheet into the rear paper clamp.

u Press the rear paper clamp lever (4) downwards and

locate it in the retaining groove.

Fittingandremovingthedustbag(g.C)

u Fit the dustbag (6) over the dust extraction outlet (2).

u Slide the dustbag onto the tool and make sure that it is

securely located.

u To remove the dustbag, pull it to the rear and off the outlet.

Use

Warning! Let the tool work at its own pace. Do not overload.

KA320E - Variable speed control

The variable speed control allows you to adapt the speed of

the tool to the workpiece material.

u Set the control knob (5) to the desired setting. Use a high

speed for wood, medium speed for veneer and synthetics

and low speed for acrylic glass, non-ferrous metals and for

removing paints.

Switchingonandoff(g.D)

u To switch the tool on, press the front part I of the on/off

switch (1).

u To switch the tool off, press the rear part O of the on/off

switch.

Emptyingthedustbag(g.C)

The dustbag (6) should be emptied every 10 minutes of use.

u Pull the dustbag (6) to the rear and off the tool.

u Hold the spout down and shake the dustbag (6) to empty

the contents.

u Slide the dustbag (6) onto the tool and make sure that it is

securely located.

Hintsforoptimumuse(g.E)

u Always hold the tool with both hands.

u Do not exert too much pressure on the tool.

u Regularly check the condition of the sanding sheet.

Replace when necessary.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker ka 320 eka in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Finnish as an attachment in your email.

The manual is 1,07 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Black Decker ka 320 eka Manual

Product: