Manual Black Decker ka 161 qs (page 8 of 76) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

390069

Zoom out

Zoom in

1/76

ENGLISH

Labels on tool

The following pictograms are shown on the tool:

Warning! To reduce the risk of injury, the user must

read the instruction manual.

Electrical safety

This tool is double insulated; therefore no earth wire

is required. Always check that the power supply

corresponds to the voltage on the rating plate.

u If the supply cord is damaged, it must be replaced by the

manufacturer or an authorised Black & Decker Service

Centre in order to avoid a hazard.

Features

This tool includes some or all of the following features.

1. On/off switch

2. Dust extraction connector

3. Base

4. Tip holder

5. Sanding base tip

6. Finger attachment

7. Prole attachment

8. Screw

9. Sanding proles

In addition, this tool is supplied with some or all of the

following accessories:

Accessory Recommended application

and use

u Coarse grit sandpaper Fast paint, varnish and rust

removal

u Medium grit sandpaper Paint, varnish and rust removal

u Fine grit sandpaper Surface blending and nishing

u Extra ne grit sandpaper Sanding between coats

u Detail sanding tips Corners and hard to reach places

u 1 OT polishing/stripping Polishing metals, stripping

wool varnish and glass cleaning

u Grey foam pad Applying and removing polish

u Red non-woven pad Heavy scrubbing and rust

removal

u Grey abrasive paper Polishing plastics

u Contour attachments Curves and proles

Assembly

Warning! Before assembly, make sure that the tool is

switched off and unplugged.

Fittingsandingsheets(g.A&B)

u Detach the two diamond-shaped tips (10) from the

sanding sheet (11).

u Hold the tool with the sanding base facing upwards.

u Place the sanding sheet (11) onto the sanding base,

making sure that the holes in the sheet line up with the

holes in the base.

The diamond-shaped tip (10) can be reversed and replaced

when worn.

u When the front part of the tip is worn, detach it from the

sheet, reverse it and press it onto the sanding base again.

u When the whole tip is worn, remove it from the sanding

base and t a new tip.

u The polishing foam and pads (14) can be tted the same

way as the sanding sheets.

Tipofthesandingbase(g.C)

When the sanding base tip (5) or tip holder (4) is worn, it can

be reversed or replaced. Spare parts are available from your

Black & Decker dealer.

u Remove the screw (8).

u Reverse or replace the worn part.

u Fit and tighten the screw.

Fingerattachment(g.D)

The nger attachment is used for ne detail sanding.

u Remove the screw (8).

u Remove the diamond-shaped tip holder (4) from the

sanding base.

u Fit the nger attachment (6) onto the sanding base.

u Fit and tighten the screw.

u Fit the appropiate sanding sheet (12) onto the nger

attachment.

Proleattachment(KA160K/KA161Konly)(g.E)

The prole attachment is used for contour sanding.

u Remove the screw (8).

u Remove the diamond-shaped tip holder (4) from the

sanding base.

u Fit the prole attachment (7) onto the sanding base.

u Fit and tighten the screw.

Fittingandremovingasandingprole(g.F1&F2)

u Choose the sanding prole most suitable for your application.

u Place one end of the sanding prole (9) into the recess at

the front end of the prole holder (7).

u Push the other end of the sanding prole until it clicks into

place.

u To remove the sanding prole, push it forward and pull the

rear end out of the prole holder (g. F2).

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker ka 161 qs in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,61 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Black Decker ka 161 qs Manual

Product: