578633
9
Zoom out
Zoom in
Previous page
1/16
Next page
9
ENGLISH
(Original instructions)
Note: Ensure that the locking ring is tight and that the side ll
canister is rmly secured in place.
Aligning the pickup tube (g. B & C)
The pickup tube can be aligned in the direction that you will be
doing the most spraying to help minimize the amount of times
that you will have to rell the canister.
u If you are spraying at an upward angle or straight on,
position the pickup tube (g. B) toward the back of the
canister.
u If you are spraying at a downward angle, position the
pickup tube (g. C) toward the front of the canister.
This will ensure you spray as much material as possible
before you need to rell.
Attaching the air hose (g. D & E)
u Insert one end of the air hose (5) into the back of the
sprayer (3). A slight twisting action when inserting the
hose will help ensure a snug t.
u Insert the other end of the air hose (5) into the back of the
power unit (4). A slight twisting action when inserting the
hose will help ensure a snug t.
Filling the canister (g. F)
u Check to make sure that the side ll canister (6) is com-
pletely screwed onto the sprayer.
u Lay the sprayer on its side with the canister side lid facing
up.
u Pour the properly thinned and strained material to be
sprayed into the side ll canister.
Note : Use the mixing bucket provided to pour material from
the original material container into the side ll canister.
u Clean any residual liquid from the threads or sides of the
canister and sprayer.
u Starting the threads evenly, screw the lid completely
onto the side ll canister. Check the lid to make sure it is
threaded on squarely and completely before picking up
the sprayer.
Use
Switching on and off (g. G)
The on/off switch is located on the handle of the power unit.
u To turn the power unit on, press the top of switch (I).
u To turn the power unit off, press the bottom of switch (0).
Warning! Never point the sprayer at any part of the body.
Never pull the trigger while adjusting the spray setting.
Selecting the spray pattern (g. H & I)
This sprayer is tted with a pattern select nozzle (10) which is
capable of 3 spray patterns. This is used to select the correct
spray pattern for your particular spraying operation.
Using the pattern select nozzle (10), choose from one of the
following applications:
Horizontal Flat Jet - Apply up and down a surface.
Circular Jet - for corners, edges and narrow surfaces.
Vertical Flat Jet. Apply side to side.
There are three spray patterns to choose from. They are
marked as 1, 2 and 3 on the pattern select label located on
the top of the sprayer (g. H)
u To select the required spray pattern, turn the pattern select
nozzle (10) and align the green indicator on the pattern
select nozzle (10) with the number on the label (g. I)
Warning! Never point the sprayer at any part of the body.
Never pull the trigger while adjusting the spray setting.
Flow control knob (g. J)
The ow control knob regulates the amount of liquid that can
be sprayed.
u Turn the ow control knob (8) clockwise to increase the
ow of liquid
u Turn the ow control knob (8) counterclockwise to
decrease the ow of liquid.
u The ow indicator (9) on the top of the sprayer moves
forward (minimal liquid ow) and backward (maximum
liquid ow) as the ow control knob (8) is turned.
Note : Always test the spray pattern on scrap cardboard
or similar material rst. Begin with ow control knob on the
highest ow setting. If less ow is desired, dial the ow control
knob in. Heavier, thicker materials should be sprayed with the
indicator close to the (+) icon. Thinner materials should be
sprayed with the indicator close to the (-) icon.
Note : If the ow control setting is set completely to the
minimum side, the trigger will have limited or no travel. Back
the ow control knob off (clockwise) to allow for more trigger
travel.
Liquid material preparation (g. K & L)
Note : Make sure the type of material you use can be cleaned
with either mineral spirits or paint thinner (for oil-based paints)
or a warm water and soap solution (for water soluble paints
like latex). Use drop cloths to protect your oors and anything
else in the spraying area that you wish to remain untouched.
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker HVLP400 T1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker HVLP400 T1 in the language / languages: English as an attachment in your email.

The manual is 3,31 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Black Decker HVLP400 T1

Black Decker HVLP400 T1 User Manual - English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish - 112 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info