32032
10
Zoom out
Zoom in
Previous page
1/104
Next page
10
ENGLISH
Mains plug replacement (U.K. & Ireland only)
Should your mains plug need replacing and
you are competent to do this, proceed as
instructed below. If you are in doubt,
contact an authorised repair agent or a
qualified electrician.
Disconnect the plug from the supply and
remove the fuse from the plug.
Cut off the plug and dispose of it safely; a plug
with bared copper conductors is dangerous if
engaged in a live socket outlet.
Only fit 13 Amperes BS1363A approved plugs
fitted with a 5 A fuse (1).
The cable wire colours, or a letter, will be
marked at the connection points of most good
quality plugs. Attach the wires to their
respective points in the plug (see above).
Brown is for Live (L) (2), blue is for Neutral (N) (4).
Before replacing the top cover of the mains
plug ensure that the cable restraint (3) is
holding the outer sheath of the cable firmly
and that the leads are correctly fixed at the
terminal screws.
If the plug has a fuse cover, make sure that the
fuse cover is fitted. Do not use the plug if the
fuse cover is missing or damaged.
Never use a light socket.
OVERVIEW (fig. A)
1. Variable speed switch
2. Forward/reverse slider
3. Mode selector / torque adjustment collar
4. Chuck
5. Two-gear selector
6. Battery charge indicator
(HP128F2/HP148F2/HP188F2)
7. Bit holder
8. Side handle (HP188F2)
9. Battery
10. Battery release button
11. Charger
12. Charging indicator
13. End of charge indicator
ASSEMBLY
Fitting and removing the battery (fig. B)
To fit the battery (9), line it up with the
receptacle on the tool. Slide the battery into
the receptacle and push until the battery snaps
into place.
To remove the battery, push the release
button (10) while at the same time pulling the
battery out of the receptacle.
Fitting and removing a drill bit or screwdriver
bit (fig. A & C)
This tool is fitted with a keyless chuck to allow for
an easy exchange of bits.
Lock the tool by setting the forward/reverse
slider (2) to the centre position (fig. A).
Open the chuck by turning the front part (15)
with one hand while holding the rear part (16)
with the other (fig. C).
Insert the bit shaft (17) into the chuck.
Firmly tighten the chuck by turning the front
part (15) with one hand while holding the rear
part (16) with the other.
This tool is supplied with a double-ended
screwdriver bit in the bit holder (7) (fig. A).
To remove the screwdriver bit from the bit
holder, lift the bit from the recess.
To store the screwdriver bit, firmly push it into
the holder.
HP126F2/HP146F2 - Removing and fitting the
chuck (fig. D)
The chuck on these models can be easily removed
and refitted. When your project entails both
drilling and screwdriving, fit a screwriver bit in the
spindle and a drill bit in the chuck: you will then
only need to remove the chuck for screwdriving
and refit it for drilling. The screwdriver bit can be
left in the spindle while drilling. You can also fit
drill bits with a hexagonal shaft in this way.
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker HP148F2K at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker HP148F2K in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,66 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Black Decker HP148F2K

Black Decker HP148F2K User Manual - English - 104 pages

Black Decker HP148F2K User Manual - English - 104 pages

Black Decker HP148F2K User Manual - English - 20 pages

Black Decker HP148F2K User Manual - German - 104 pages

Black Decker HP148F2K User Manual - German - 104 pages

Black Decker HP148F2K User Manual - Dutch - 104 pages

Black Decker HP148F2K User Manual - Dutch - 104 pages

Black Decker HP148F2K User Manual - Danish - 104 pages

Black Decker HP148F2K User Manual - Danish - 104 pages

Black Decker HP148F2K User Manual - French - 104 pages

Black Decker HP148F2K User Manual - French - 104 pages

Black Decker HP148F2K User Manual - Italian - 104 pages

Black Decker HP148F2K User Manual - Italian - 104 pages

Black Decker HP148F2K User Manual - Portuguese, Swedish - 104 pages

Black Decker HP148F2K User Manual - Swedish - 104 pages

Black Decker HP148F2K User Manual - Norwegian, Finnish - 104 pages

Black Decker HP148F2K User Manual - Finnish - 104 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info