Manual Black Decker HP128F2K (page 12 of 104) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Norwegian, Finnish)

31996

Zoom out

Zoom in

1/104

ENGLISH

Large screws and hard workpiece materials require a

higher torque setting than small screws and soft

workpiece materials. The collar has a wide range of

settings to suit your application.

◆ For drilling in wood, metal and plastics, set the

collar (3) to the drilling position by aligning the

symbol

with the marking (24).

◆ HP148F2/HP188F2:

For drilling in masonry, set the collar (3) to the

hammer drilling position by aligning the

symbol with the marking (24).

◆ For screwdriving, set the collar to the desired

setting. If you do not yet know the appropriate

setting, proceed as follows:

◆ Set the collar (3) to the lowest torque setting.

◆ Tighten the first screw.

◆ If the clutch ratchets before the desired

result is achieved, increase the collar setting

and continue tightening the screw.

Repeat until you reach the correct setting.

Use this setting for the remaining screws.

Two-gear selector (fig. I)

◆ For drilling in steel and for screwdriving

applications, slide the two-gear selector (5)

towards the front of the tool (1st gear).

◆ For drilling in materials other than steel, slide

the two-gear selector (5) towards the rear of

the tool (2nd gear).

Drilling/screwdriving (fig. A)

◆ Select forward or reverse rotation using the

forward/reverse slider (2).

◆ To switch the tool on, press the switch (1).

The tool speed depends on how far you press

the switch.

◆ To switch the tool off, release the switch.

Hints for optimum use

Drilling

◆ Always apply a light pressure in a straight line

with the drill bit.

◆ Just before the drill tip breaks through the

other side of the workpiece, decrease pressure

on the tool.

◆ Use a block of wood to back up workpieces

that may splinter.

◆ Use spade bits when drilling large diameter

holes in wood.

◆ Use HSS drill bits when drilling in metal.

◆ Use masonry bits when drilling in soft masonry.

◆ Use a lubricant when drilling metals other than

cast iron and brass.

◆ Make an indentation using a centre punch at

the centre of the hole to be drilled in order to

improve accuracy.

Screwdriving

◆ Always use the correct type and size of

screwdriver bit.

◆ If screws are difficult to tighten, try applying a

small amount of washing liquid or soap as a

lubricant.

◆ Always hold the tool and screwdriver bit in a

straight line with the screw.

MAINTENANCE

Your Black & Decker tool has been designed to

operate over a long period of time with a

minimum of maintenance. Continuous satisfactory

operation depends upon proper tool care and

regular cleaning.

Your charger does not require any maintenance

apart from regular cleaning.

Before performing any maintenance on

the tool, remove the battery from the tool.

◆ Unplug the charger before cleaning it.

◆ Regularly clean the ventilation slots in your tool

and charger using a soft brush or dry cloth.

◆ Regularly clean the motor housing using a

damp cloth. Do not use any abrasive or

solvent-based cleaner.

◆ Regularly open the chuck and tap it to remove

any dust from the interior.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker HP128F2K in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Norwegian, Finnish as an attachment in your email.

The manual is 0,66 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Black Decker HP128F2K

Black Decker HP128F2K User Manual - English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish - 104 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Black Decker HP128F2K Manual

Product: