472986
12
Zoom out
Zoom in
Previous page
1/104
Next page
12
ENGLISH
Large screws and hard workpiece materials require a
higher torque setting than small screws and soft
workpiece materials. The collar has a wide range of
settings to suit your application.
For drilling in wood, metal and plastics, set the
collar (3) to the drilling position by aligning the
symbol
with the marking (24).
HP148F2/HP188F2:
For drilling in masonry, set the collar (3) to the
hammer drilling position by aligning the
symbol with the marking (24).
For screwdriving, set the collar to the desired
setting. If you do not yet know the appropriate
setting, proceed as follows:
Set the collar (3) to the lowest torque setting.
Tighten the first screw.
If the clutch ratchets before the desired
result is achieved, increase the collar setting
and continue tightening the screw.
Repeat until you reach the correct setting.
Use this setting for the remaining screws.
Two-gear selector (fig. I)
For drilling in steel and for screwdriving
applications, slide the two-gear selector (5)
towards the front of the tool (1st gear).
For drilling in materials other than steel, slide
the two-gear selector (5) towards the rear of
the tool (2nd gear).
Drilling/screwdriving (fig. A)
Select forward or reverse rotation using the
forward/reverse slider (2).
To switch the tool on, press the switch (1).
The tool speed depends on how far you press
the switch.
To switch the tool off, release the switch.
Hints for optimum use
Drilling
Always apply a light pressure in a straight line
with the drill bit.
Just before the drill tip breaks through the
other side of the workpiece, decrease pressure
on the tool.
Use a block of wood to back up workpieces
that may splinter.
Use spade bits when drilling large diameter
holes in wood.
Use HSS drill bits when drilling in metal.
Use masonry bits when drilling in soft masonry.
Use a lubricant when drilling metals other than
cast iron and brass.
Make an indentation using a centre punch at
the centre of the hole to be drilled in order to
improve accuracy.
Screwdriving
Always use the correct type and size of
screwdriver bit.
If screws are difficult to tighten, try applying a
small amount of washing liquid or soap as a
lubricant.
Always hold the tool and screwdriver bit in a
straight line with the screw.
MAINTENANCE
Your Black & Decker tool has been designed to
operate over a long period of time with a
minimum of maintenance. Continuous satisfactory
operation depends upon proper tool care and
regular cleaning.
Your charger does not require any maintenance
apart from regular cleaning.
Before performing any maintenance on
the tool, remove the battery from the tool.
Unplug the charger before cleaning it.
Regularly clean the ventilation slots in your tool
and charger using a soft brush or dry cloth.
Regularly clean the motor housing using a
damp cloth. Do not use any abrasive or
solvent-based cleaner.
Regularly open the chuck and tap it to remove
any dust from the interior.
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker HP126 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker HP126 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,66 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info