584874

Black Decker GXC1000 TH1 Manual

6
Zoom out
Zoom in
Previous page
1/88
Next page
6
ENGLISH
Chargers
Use your Black & Decker charger only to charge the battery
in the tool with which it was supplied. Other batteries could
burst, causing personal injury and damage.
Never attempt to charge non-rechargeable batteries.
Have defective cords replaced immediately.
Do not expose the charger to water.
Do not open the charger.
Do not probe the charger.
The charger is intended for indoor use only.
Fail safe isolating transformer. The mains supply is
electrically separated from the transformer output.
The charger automatically shuts off if the ambient
temperature becomes too high. As a consequence
the charger will be inoperable. The charger must be
disconnected from the mains supply and taken to an
authorised service centre for repair.
Read the instruction manual before use.
Electrical safety
Your charger is double insulated; therefore no earth
wire is required. Always check that the mains voltage
corresponds to the voltage on the rating plate.
Warning! Never attempt to replace the charger unit with a
regular mains plug.
If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised Black & Decker Service
Centre in order to avoid a hazard.
Features
1. On/off switch
2. Lock-off button
3. Main handle
4. Secondary handle
5. Handle knob
6. Handle adjustment collar
7. Motor housing
8. Shroud
9. Tine assembly
10. Battery
Fig. A
11. Charger
12. Charger receptacle
13. Charging indicator
14. End of charge indicator
Assembly
Warning! Before assembly, remove the battery from the tool.
Fitting and removing the battery (fig. B)
To fit the battery (10), line it up with the receptacle on the
tool. Slide the battery into the receptacle and push until
the battery snaps into place.
To remove the battery, push the release button (15) while
at the same time pulling the battery out of the receptacle.
Fitting the battery cap (fig. C)
Warning! Fit the cap (16) to the battery (10) for transportation
and storage.
Fitting the shroud (fig. D)
Warning! Never operate the tool with a damaged shroud or
without the shroud in place.
Place the shroud (9) onto the tool as shown, aligning the
tabs (17) with the lugs (18) on the tool.
Press the shroud until it snaps into place (A).
Check that the shroud is fitted correctly.
Warning! Never use the tool unless the shroud is properly fitted.
Fitting the tines (fig. E)
Place the first tine (9) onto the shaft (19).
Insert the pin (20) into hole in the shaft.
Push the pin firmly until it clicks into place.
Repeat as for the other tine.
Use
Warning! Let the tool work at its own pace. Do not overload.
Charging the battery (fig. A)
The battery needs to be charged before first use and
whenever it fails to produce sufficient power on jobs that were
easily done before. When charging the battery for the first
time, or after prolonged storage, it will only accept an 80%
charge. After several charge and discharge cycles, the battery
will attain full capacity. The battery may become warm while
charging; this is normal and does not indicate a problem.
Warning! Do not charge the battery at ambient temperatures
below 4 °C or above 40 °C. Recommended charging
temperature: approx. 24 °C.
8 hour charger
To charge the battery (10), remove it from the tool and
slide the charger receptacle (12) onto the battery.
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker GXC1000 TH1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker GXC1000 TH1 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,08 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Black Decker GXC1000 TH1

Black Decker GXC1000 TH1 Quick start guide - English - 12 pages

Black Decker GXC1000 TH1 User Manual - Polish - 16 pages

Black Decker GXC1000 TH1 User Manual - Turkish - 12 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info