474474

Black Decker GX635 Manual

7
Zoom out
Zoom in
Previous page
1/64
Next page
7
ENGLISH
• On long grass, above 10cm (4 inches), use two
cuts to get a close finish. We recommend that
the first cut should be taken with the blade set at
maximum height of cut and the second taken
with it set at medium or close. This will prove to
be easier and give a better overall finish to
your lawn.
Care and maintenance
The advice given in this section covers the
general care and maintenance of the main
body of your mower. Advice relating to the
blades is given in “Maintenance of blades”.
!
Warning! Do not use an extension cable
which shows signs of damage. Fit a new
cable completely - do not make any
permanent or temporary repairs.
• Always keep your mower clean and free
from grass cuttings, especially the
underside of the cutter cover and the air
vents.
• Check all electrical cables at regular
intervals, looking for signs of wear,
abrasion or other damage.
• At the end of each cutting session we
recommend that the build up of grass on
the underside of the cutter cover is
removed using a blunt scraper or the
spanner supplied.
• Remove grass cuttings from the slot
between the pivot block flanges.
• Clean all plastic components with a
damp cloth.
Caution: Do not use solvents or cleaning
fluids as these may damage the plastic
components of your mower.
Fault finding
If your mower does not operate correctly,
use the following table to locate the problem.
!
Warning! Always disconnect your mower
from the electrical supply before carrying out
any inspection.
Symptoms Possible cause Remedy
Motor buzzes Blade jammed. Disconnect from
but blade does the electrical
not move. supply.
Remove the
obstruction from
the blade.
No noise and Faulty electrical Disconnect from
the blade does connection. the electrical
not move. supply.
Symptoms Possible cause Remedy
No noise and Faulty electrical Plug your mower
the blade does connection. into an alternative
not move. compatible
electrical supply.
Check if a new
fuse is required.
Re-tighten and
check all electrical
connections in the
extension cables.
Overload cut- Reset overload
out operates. cut-out.
Grass not being The grassbox Empty the
picked up. is full. grassbox.
The pickup inlet Remove grassbox
in the grassbox and clear the hole
is blocked. in the base.
Air paths are Remove grassbox
blocked. and clear the filter
in the roof of the
grassbox.
Also clean the
filter on the back
of your mower.
The cut height Disconnect from
is too low in the electrical
long grass. supply. Reset
the blade height
to a higher
position.
Your mower Push your mower
is being moved in a straight line to
side to side. maximise pick up.
Motor stalled. The motor is Disconnect from
overloading in the electrical
long, thick supply. Reset the
grass. blade height
to a higher
position.
Poor cutting Blade damaged Disconnect from
performance. due to impact the electrical
on large stones, supply. Check the
tree stumps, blade for damage.
paving stones or Replace with a
similar objects. new blade,
if necessary.
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker GX635 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker GX635 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 0,79 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info