Manual Black Decker GW200 T4 (page 10 of 60) (English, German, Dutch, French, Italian, Portuguese, Spanish)

586134

Zoom out

Zoom in

1/60

Warning! The use of an RCD or other

circuit breaker unit does not release the

operator of your product from the safety

instructions and safe working practices

given in this manual.

Assembly prior to use (Fig. B & F)

Vacuum tube assembly (Fig. B1)

• Vacuum tubes must be assembled

together before use.

• To ease assembly apply soapy water

solution to joint area.

• Align location ribs on upper (4) and

lower (5) tubes.

• Push both parts firmly together until clip

is engaged, as per moulded detail.

(Never operate apart).

• In the interests of safety, it is not

intended for the tubes to be separated

once assembled.

Blow tube assembly (Fig. B2)

• Blow tubes must be assembled

together before use.

• To ease assembly, apply a soapy water

solution to the joint area.

• Align location ribs on the upper (6) and

the lower (7) tubes.

• Push both parts firmly together until the

clip is engaged (never operate apart).

• In the interests of safety, it is not

intended for the tubes to be separated

once assembled.

Blow tube assembly (GW254) (Fig. B3)

• Fit the lower tube (14) over the middle

tube (13), until the lock button (15)

clicks in place.

• Align the cross mark on theassembled

blow tube with the cross mark on the

upper blow tube (6).

• Insert the assembled blow tube into the

upper blow tube and turn it to lock it in

place.

• Alternatively, the flexi-piece (16) can be

fitted between the upper blow tube and

the assembled blow tube. With the

flexi-piece, the unit can be handled

more easily and with greater control.

Carrying strap assembly (GW250) (Fig. B4)

• Fit the carrying strap to the powerhead,

if required, and adjust to suit the user.

Warning! The shoulder strap should only

be used during vacuum mode. Never use

the strap during blow mode.

Carrying strap assembly (GW254)

(Fig. B5 & B6)

For use in flexi-blow or vacuum mode.

• Fit the small loop over the T-handle.

• Adjust the large loop to suit the user.

• The unit can now be hung over the

shoulder and handled as shown.

Collection bag (GW225) (Fig. F8)

• Attach the collection bag to the vacuum

outlet using the bayonet fitting.

On/off switch (Fig. C)

• The on/off switch (2) is located on the

handle of the powerhead.

• To switch your product on, push the

switch forward.

• The switch will not operate if the release

button (3) is depressed.

• To switch off, push the switch to the rear.

Cable restraint (Fig. D)

• A cable restraint is incorporated into the

rear of the powerhead.

• To fix cable, form a loop in the cable

and insert as shown.

Using your product (Fig. E)

When using as a blower or vacuum, always

wear safety glasses. If using in dusty

conditions, wear a filter mask as well.

Blow mode (GW250/GW254)

• Ensure your product is switched off and

disconnected from the mains power

supply.

• Attach the blow tube (6) to the

powerhead (1) (Fig. E1) by locating the

tube as shown, then pivot about this

point until the locking/release catch is

fully engaged (Fig. E2).

• Hold the blow tube approximately

180mm (7”) above the ground, switch

your product on and using a sweeping

motion from side to side, advance

slowly keeping the accumulated debris/

leaves in front of you (Fig. E4).

Blow control (GW225/GW250) (Fig. E5)

• Position A - Maximum blow speed.

• Position B - Blow control can be varied

between positions A and C. To do this,

depress the latch as shown and slide

the control forward/backward to obtain

desired airspeed, then release the latch

to lock.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker GW200 T4 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 1,48 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Black Decker GW200 T4

Black Decker GW200 T4 User Manual - Danish, Swedish, Norwegian, Finnish - 32 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Black Decker GW200 T4 Manual

Product: