665758

Black Decker GT200 series Manual

8
Zoom out
Zoom in
Previous page
1/40
Next page
7
ENGLISH
terminal screws
clamping washers
connector body fixing screw
6mm
cable
clamp cover
cable
protector
Assembly instructions
• To avoid risk of injury, it is advisable to leave the
blades in their cardboard cover until the front
handle has been fitted.
You will need a No 2 Posidrive screwdriver.
Fitting the front handle
(Please see diagram 2)
• Clamp the handle (1) into the recesses (2) on the
side of the unit.
• Pass the large screws (3) through the handle into
the body, and tighten.
Fitting the guard
(Please see diagram 3)
• Slide the guard over the length of the blade and
locate onto the recesses on the side of the body.
• Insert the two guard fixing screws through the
sides of the guard into the unit body and tighten.
Note: The guard and handle must always be fitted to
the unit for protection of the user.
Operation of your hedgetrimmer
(Please refer to diagram 4)
• Models with lock-off switch:
• TO SWITCH ON
• Press in lock-off button (A) and squeeze the
trigger (B)
• TO SWITCH OFF
• Release the trigger.
• For units with a brake mechanism:
• SWITCHING ON
• The motor may start momentarily before
the blades begin to move. By fully depressing
the switch trigger, drive to the blades will
be connected and then the blades will begin
to move.
• SWITCHING OFF
• The motor may run on after the blades have
stopped. This is perfectly normal.
Electronic (
Please see diagram
5)
• Models with electronic speed control:
Alter the speed to suit the application -
Low speed for light trimming.
High speed for fast hedge trimming.
Switch off before changing speed settings.
The speed of the blades can be adjusted from High
speed to Low speed by rotating the control knob.
Low speed is obtained when No. 1 on the knob
is visible.
High speed is obtained when No. 2 on the knob
is visible.
Cutting techniques for better results
(Please see diagrams 6.1 to 6.5)
• The blades will cut most effectively when they are
not exactly parallel with the line of cut, but have
the tips of the blades pointing slightly towards
the hedge. This lateral tilt should not exceed 5
0
to
the line of cut.
• Most users trim the top of a hedge first. Hold the
tool at the desired angle and move it steadily
along the line of cut. The double edged blade
enables you to cut in either direction or with a
side to side movement.
• For a very level finish, a piece of string can be
stretched along the length of the hedge at the
required height to serve as a guide. The hedge
may be cut just above the string.
• To keep very flat sides it is better to cut upwards
with the growth. Cutting downwards can
produce an uneven result.
• Take care to avoid hard objects, such as wire,
which could cause damage to cutting blades.
Remember that your hedgetrimmer is also suitable
for clipping most shrubs or brambles.
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker GT200 series at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker GT200 series in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 1,37 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info