Manual Black Decker GSL700 (page 7 of 100) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

630499

Zoom out

Zoom in

1/100

ENGLISH

(Original instructions)

Warning! The battery uid may cause personal injury or

damage to property. In case of skin contact, immediately rinse

with water. If redness, pain or irritation occurs seek medical

attention. In case of eye contact, rinse immediately with clean

water and seek medical attention.

Chargers

Your charger has been designed for a specic voltage.

Always check that the mains voltage corresponds to the

voltage on the rating plate.

Warning! Never attempt to replace the charger unit with

a regular mains plug.

u Use your Black & Decker charger only to charge the

battery in the tool with which it was supplied. Other

batteries could burst, causing personal injury and damage.

u Never attempt to charge non-rechargeable batteries.

u If the supply cord is damaged, it must be replaced by the

manufacturer or an authorised Black & Decker Service

Centre in order to avoid a hazard.

u Do not expose the charger to water.

u Do not open the charger.

u Do not probe the charger.

u The appliance/tool/battery must be placed in a well

ventilated area when charging.

The charger is intended for indoor use only.

Read the instruction manual before use.

The charger automatically shuts off if the ambient

temperature becomes too high. As soon as the

ambient temperature has cooled down, the charger

will resume operating.

Fail safe isolating transformer. The mains supply is

electrically separated from the transformer output.

Electrical safety

Your charger is double insulated; therefore no earth

wire is required. Always check that the mains

voltage corresponds to the voltage on the rating

plate.

u If the supply cord is damaged, it must be replaced by the

manufacturer or an authorised Black & Decker Service

Centre in order to avoid a hazard.

u Warning! Never attempt to replace the charger unit with

a regular mains plug.

Features

1. On/off switch

2. Lock-off button

3. Blade release button

4. Shear blade (GSL200/GSL360/GSL700)

5. Trim blade (GSL300/GSL360/GSL700)

6. Charging indicator

Assembly

Warning! Avoid accidentally switching the tool on during

assembly.

Fitting the wall mount to the wall (g. A & B)

The wall mount can be tted to the wall to provide a

convenient storage and charging point for the tool.

u Drive the screws in the wall through the holes in the

crevices of wall mount.

u Place the tool on the wall mount.

u Plug in the charger making sure the charging indicator (6)

lights up (fig. A).

u If required, use the two pegs (7) below the wall mount to

store the spare blade (fig. B).

Warning! Avoid damaging the power cord when mounting the

wall mount to the wall.

Removing the charger plug from the wall mount

(g. C)

The tool can be charged without using the wall mount. The

charger plug can be connected to the tool directly.

u Remove the screws from the back of the wall mount.

u Slide the back part (8) from the front part (9) to open the

wall mount.

u Remove the charger plug from the wall mount.

Fitting and removing the blade (g. D & E)

The shear blade (4) has been designed for trimming grass

and weeds. The trim blade (5) has been designed for trimming

hedges and shrubs.

u Remove the blade cover.

u Push and hold the blade release button (3) in the direction

of the arrow (fig. D1).

u Slide the blade cover (10) backward and lift off (fig. D2).

u Lower the blade onto the pins.

u While holding the blade onto the pins (fig. E1), replace the

blade cover (10) and slide it forward (fig. E2).

Note: No alignment of blade with drive pin is required and

operation of the blade cover release button is not required

when re-tting the blade cover.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker GSL700 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 5,52 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Black Decker GSL700 Manual

Product: