Manual Black Decker GRC4736SD (page 13 of 152) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Spanish, Norwegian, Finnish)

474479

Zoom out

Zoom in

1/152

ENGLISH

(Original instructions)

Maintenance

Your Black & Decker corded/cordless appliance/tool has been

designed to operate over a long period of time with a minimum

of maintenance. Continuous satisfactory operation depends

upon proper tool/appliance care and regular cleaning.

Your charger does not require any maintenance apart from

regular cleaning.

Warning! Before performing any maintenance on corded/

cordless power tools:

u Switch off and unplug the appliance/tool.

u Or switch off and remove the battery from the appliance/

tool if the appliance/tool has a separate battery pack.

u Or run the battery down completely if it is integral and then

switch off.

u Unplug the charger before cleaning it. Your charger does

not require any maintenance apart from regular cleaning.

u Regularly clean the ventilation slots in your tool/appliance

and charger using a soft brush or dry cloth.

u Regularly clean the motor housing using a damp cloth. Do

not use any abrasive or solvent-based cleaner.

u Regularly use a blunt scraper to remove grass and dirt

from the underneath of the guard.

Removing and installing the blade (g. R & S)

Warning! Do not touch the blade before the safety key has

been removed and the blades have come to a complete stop.

u Release the bail bar (3) to turn mower off, wait for the

blade to stop and remove the safety key (1).

u Cut a piece of wood (approximately 50 mm x 100 mm x

600 mm long) to use to keep the blade from turning while

removing the ange nut.

u Turn the mower on its side.

Warning! Wear gloves and proper eye protection. Be careful

of the sharp edges of the blade.

u Position the wood (32) and remove the ange nut (30)

with a 19 mm wrench (31) (g. R).

u Remove the square metal blade spacer (37), the square

plastic blade insulator (33) and the blade (34) (g S).

Examine the blade insulator (35) for damage and replace

if necessary.

When tting the blade, make sure that the grass side of the

blade will face the ground when the mower is returned to its

normal upright position.

u After installing the blade, place the blade insulator (35)

on the blade such that the raised lips on one side engage

with the edges of the blade (34).

u Install the blade spacer (36) so that it sits inside the raised

lips on the other side of the blade insulator (35). Be sure

to align the ats in the hole of the blade spacer (36) with

the ats of the shaft, rotating the blade and blade insulator

together as necessary.

u Position the piece of wood (32) to keep the blade from

turning (g. R).

u Install the ange nut (30) with the ange against the

square metal blade spacer (37) and tighten.

Blade sharpening (g. T)

Keep the blade sharp for best performance. A dull blade does

not cut grass cleanly or mulch properly.

Warning! Always make sure that the safety key is removed.

Warning! Wear proper eye protection while removing, sharp-

ening and installing a blade.

Sharpening the blade twice during a mowing season is usually

sufcient under normal circumstances. Sand causes the

blade to dull quickly. If your lawn has sandy soil more frequent

sharpening may be required.

u Replace bent or damaged blades immediately.

When sharpening the blade:

u Make sure that the blade remains balanced.

u Sharpen the blade at the original cutting angle.

u Sharpen the cutting edges on both ends of the blade,

removing equal amounts of material from both ends.

To sharpen a blade in a vice (g. T)

u Release the bail bar (3) to turn the lawnmower off and wait

for the blade to come to a complete stop.

u Remove the safety key (1) and the battery pack (11) and

turn the lawnmower on to its side.

u Remove the blade (34) from the mower, see the instruc-

tions for removing and installing blades.

Warning! Wear proper eye protection and gloves and be

careful of the sharp edges of the blade.

u Put the blade (34) in a vice.

u Carefully le the cutting edges of the blade with a ne

tooth le or a sharpening stone, maintaining the original

cutting edge.

u Check the balance of the blade, see the instructions for

blade balancing.

u Install the blade (34) on the mower and tighten securely,

see the instructions for removing and installing blades.

Blade balancing (g. U)

u Check the balance of the blade by putting the centre hole

in the blade on to a nail or a round shank screwdriver that

is clamped horizontally in a vice. If either end of the blade

rotates downward, le that end of the blade until the blade

is balanced.

Lubrication

No lubrication is necessary. Do not oil the wheels. They have

plastic bearing surfaces which require no lubrication.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker GRC4736SD in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 7,5 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Black Decker GRC4736SD Manual

Product: