Manual Black Decker GR230 (page 5 of 64) (English, German, Dutch, French, Italian, Portuguese, Spanish)

474458

Zoom out

Zoom in

1/64

ENGLISH

Note: The switch box should be positioned

on the right hand side of your mower when

viewed from the operating position. Ensure

that the electrical supply cables to and from

the switchbox are not damaged or twisted

before you begin to assemble your mower.

• Locate the lower handles (1) over the

grassflap axle (2) and position the flange

on the handles into the rectangular

aperture in the deck (3).

• Fit a plain washer (5) and then fit the

wing nut (6) onto the axle. The plain

washers and wing nuts can be found in

the parts pack. Tighten each wing nut

with hand pressure only.

• Place the upper handle (7) into the cups

of the lower handles and align the holes

in the upper and lower handles. Fit a bolt

(8) through each hole. Fit a plain washer

and then fit the wing nuts onto the bolts.

Tighten each one with hand pressure only.

Note: Do not use a spanner or other

implement to tighten the wing nuts.

Fit the switchbox to the upper handle

as follows:

• Remove the two screws holding the

retaining plate to the main body of

the switchbox.

• Locate the two pins on the switchbox

with the holes in the upper handle.

• Fit the retaining plate over the stem of the

handle using the two screws provided.

Note: Do not overtighten these screws -

light pressure will be sufficient to hold the

switchbox in position.

Wheel assembly and height of cut

adjustment (Fig. C)

Before wheel assembly adjustment ensure

your mower is disconnected from the mains.

Each of the four wheels has its own means

of height adjustment which gives 3 cutting

height positions.

• Select one of the tapped holes in the

mounting plate (9) and note it as the

other three wheels will have to be

adjusted to the same position.

• Locate the wheel (10), and the screw bolt

(11) into the selected hole and ensure the

washer (12) is present on the bolt

between wheel and cutter deck.

• Position nut (21) behind chosen hole in

the mounting plate.

• Use the spanner provided and turn the

screw bolt in a clockwise direction.

Ensure the wheel is free to rotate.

Using the same height adjustment position

repeat the procedure for each of the other

three wheels.

The bottom tapped hole in the mounting

plate will give a maximum height of cut which

is suitable for coarse or overgrown grass.

The top hole should be used for maintaining

cultivated lawns, and the middle hole is for

intermediate conditions.

We recommend that the middle hole or

bottom hole is selected for the first use of

your lawnmower.

Grassbox assembly (Fig. D)

Read the safety instructions at the beginning

of this manual before using this accessory.

• The grassbox is supplied in two parts

which slot together.

Fitting the grassbox to your mower:

• The spring loaded rear flap (15) is lifted

and the top of the grassbox is placed

over the mounting.

• The rear flap can now be released to lock

the grassbox into position.

Removing the grassboxfrom your mower:

The full grassbox may be removed by raising

the grassflap, freeing the grassbox from its

mounting and resting it on the lawn. The

grassflap can be gently lowered, leaving both

hands free to lift the full grassbox.

How to use your mower (Fig. E)

Observe all of the relevant warnings when

using your mower.

We recommend the directional method of

operation to obtain the maximum cutting

performance from your mower and to reduce

the risk of the trailing the extension lead from

entering the cutting path.

• Place the bulk of the supply cable on

the lawn close to the starting point

(see Fig. E1 (a), position 1).

• Hold the handle assembly with both

hands.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker GR230 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 0,93 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Black Decker GR230 Manual

Product: