Manual Black Decker GPC1820L TH1 (page 8 of 116) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

585886

Zoom out

Zoom in

1/116

ENGLISH

(Original instructions)

♦ Align the groove on the outside of the coupling end of the

handle (3) with the tongue on the inside of the coupling

end of the saw head (4). Push the saw head (4) onto the

handle (3).

♦ Slide the collar (14) down and rotate it clockwise until it is

fully tightened.

Warning! Periodically check the connections to ensure that

they are tightened securely.

Extending the saw head (g. D)

The maximum reach can be achieved by tting the extension

tube (10) between the saw head (4) and the handle (3).

♦ Align the groove on the outside of the coupling end of the

handle (3) with the tongue on the inside of the coupling

end of the extension tube (10).

♦ Push the extension tube (10) onto the handle (3).

♦ Slide the collar (15) down and rotate it clockwise until it is

fully tightened.

♦ Align the groove on the outside of the coupling end of the

extension tube (10) with the tongue on the inside of the

coupling end of the saw head (4).

♦ Push the saw head (4) onto the extension tube (10).

♦ Slide the collar (14) down and rotate it clockwise until it is

fully tightened.

Warning! Periodically check the connections to ensure that

they are tightened securely.

Removing the saw head (g. C & D)

If the extension tube (10) is tted, the saw head must be

removed rst.

♦ To remove the saw head (4), rest the handle (3) on the

ground, loosen the collar (14) and take off the saw head.

Use

Warning! Let the tool work at its own pace. Do not

overload.

Charging the battery (g. A)

The battery needs to be charged before rst use and

whenever it fails to produce sufcient power on jobs that were

easily done before.

The battery may become warm while charging; this is normal

and does not indicate a problem.

Warning! Do not charge the battery at ambient

temperatures below 10°C or above 40°C. Recommended

charging temperature: approximately. 24°C.

Note: The charger will not charge a battery if the cell

temperature is below approximately 10°C or above 40°C.

♦ The battery should be left in the charger and the

charger will begin to charge automatically when the cell

temperature warms up or cools down.

♦ To charge the battery (11), remove it from the tool and

insert it into the charger (12). The battery will only t into

the charger in one way. Do not force. Be sure that the

battery is fully seated in the charger.

♦ Plug in the charger and switch on at the mains.

♦ The charging indicator (24) will ash green continuously

(slowly).

The charge is complete when the charging indicator (24)

lights green continuously. The charger and the battery can

be left connected indenitely with the LED illuminated. The

LED will change to ashing green (charging) state as the

charger occasionally tops off the battery charge. The charging

indicator (24) will be lit as long as the battery is connected to

the plugged-in charger.

♦ Charge discharged batteries within 1 week. Battery life

will be greatly diminished if stored in a discharged state.

Leaving the battery in the charger

The charger and battery pack can be left connected

indenitely with the LED lit. The charger will keep the battery

pack fresh and fully charged.

Charger diagnostics

If the charger detects a weak or damaged battery, the

charging indicator (24) will ash red at a fast rate. Proceed

as follows:

♦ Re-insert the battery (11).

♦ If the charging indicator continues ashing red at a fast

rate, use a different battery to determine if the charging

process works properly.

♦ If the replaced battery charges correctly, the original

battery is defective and should be returned to a service

centre for recycling.

♦ If the new battery gives the same indication as the

original battery, take the charger to be tested at an

authorised service centre.

Note: It may take as long as 60 minutes to determine that

the battery is defective. If the battery is too hot or too

cold, the LED will alternately blink red, fast and slow, one

ash at each speed and repeat.

Switching on and off (g. E)

For your safety, this tool is equipped with a double switching

system. This system prevents starting the tool inadvertently.

Switching on

♦ Push the lock-off button (2) backward using your thumb

and at the same time squeeze the on/off switch (1).

♦ Release the lock-off button (2).

Switching off

♦ Release the on/off switch (1).

Warning! Never attempt to lock a switch in the on position.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker GPC1820L TH1 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 7,26 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Black Decker GPC1820L TH1

Black Decker GPC1820L TH1 Quick start guide - English - 16 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Black Decker GPC1820L TH1 Manual

Product: