585843

Black Decker GPC1800 TH1 Manual

8
Zoom out
Zoom in
Previous page
1/124
Next page
Electrical safety
#
Your charger is double insulated;
therefore no earth wire is required.
Always check that the mains voltage
corresponds to the voltage on the rat-
ing plate. Never attempt to replace the
charger unit with a regular mains plug.
Overview
1. On/off switch
2. Lock-off button
3. Main handle
4. Saw head
5. Sprocket cover
6. Guide bar
7. Chain
8. Chain sheath
9. Lubrication bottle
10. Extension tube
11. Battery
Fig. A
12. Charger
Assembly
Warning! Before assembly, remove the battery
from the tool.
Fitting and removing the battery (g. B)
• To t the battery (11), line it up with the
receptacle on the tool. Slide the battery into the
receptacle and push until the battery snaps into
place.
• To remove the battery, push the release button
(13) while at the same time pulling the battery
out of the receptacle.
Warning! To prevent accidental operation,
ensure that the battery is removed and that
the chain sheath is in place on the saw chain
before performing the following operations.
Failure to do this could result in serious per-
sonal injury.
Fitting the saw head (g. C)
The saw head can be tted directly to the handle in
order to achieve standard reach.
• Align the groove on the outside of the coupling
end of the handle (3) with the tongue on the
inside of the coupling end of the saw head (4).
Push the saw head (4) onto the handle (3).
• Slide the collar (14) down and rotate it
clockwise until it is fully tightened.
Warning! Periodically check the connections to
ensure that they are tightened securely.
Extending the saw head (g. D)
The maximum reach can be achieved by tting the
extension tube (10) between the saw head (4) and
the handle (3).
• Align the groove on the outside of the coupling
end of the handle (3) with the tongue on the
inside of the coupling end of the extension tube
(10).
• Push the extension tube (10) onto the handle
(3).
• Slide the collar (15) down and rotate it
clockwise until it is fully tightened.
• Align the groove on the outside of the coupling
end of the extension tube (10) with the tongue
on the inside of the coupling end of the saw
head (4).
• Push the saw head (4) onto the extension tube
(10).
• Slide the collar (14) down and rotate it
clockwise until it is fully tightened.
Warning! Periodically check the connections to
ensure that they are tightened securely.
Removing the saw head (g. C & D)
If the extension tube (10) is tted, the saw head
must be removed rst.
• To remove the saw head (4), rest the handle (3)
on the ground, loosen the collar (14) and take
off the saw head.
Use
Warning! Let the tool work at its own pace. Do
not overload.
Charging the battery (g. A)
The battery needs to be charged before rst use
and whenever it fails to produce sufcient power
on jobs that were easily done before. When charg-
ing the battery for the rst time, or after prolonged
storage, it will only accept an 80% charge.
After several charge and discharge cycles, the
battery will attain full capacity. The battery may
become warm while charging; this is normal and
does not indicate a problem.
Warning! Do not charge the battery at ambi-
ent temperatures below 10 °C or above 40 °C.
Recommended charging temperature: approx.
24°C.
8
ENGLISH
(Original instructions)
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker GPC1800 TH1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker GPC1800 TH1 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 4,16 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Black Decker GPC1800 TH1

Black Decker GPC1800 TH1 Quick start guide - English - 16 pages

Black Decker GPC1800 TH1 User Manual - Polish - 16 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info