583864

Black Decker GL716 T2 Manual

6
Zoom out
Zoom in
Previous page
1/76
Next page
6
ENGLISH
Assembly
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
Fitting the guard (fig. A)
◆ Remove the hexagonal screws (13) from the head (14).
◆ Place the guard (8) onto the tool as shown.
◆ Firmly press the guard until it snaps into place.
◆ Secure the guard with the hexagonal screws.
◆ Tighten the hexagonal screws using the hexagonal key (15)
provided
Warning! Never use the tool unless the guard is properly
fitted.
Releasing the cutting line
In transit, the cutting line is taped to the spool housing.
◆ Remove the tape holding the cutting line (11) to the spool
housing (10).
Connecting the tool to the mains
◆ Connect the female plug of a suitable extension cable to
the power inlet (4).
◆ Loop the cable through the cable restraint (3).
◆ Insert the mains plug into a mains outlet.
Warning! The extension cable must be suitable for outdoor use.
Use
Warning! Let the tool work at its own pace. Do not overload.
Setting the tool to trimming or edging mode (fig. B - D)
The tool can be used in trimming mode as shown in fig. B or in
edging mode to trim overhanging grass along lawn edges and
flower beds as shown in fig. C.
Trimming mode (fig. B & D)
For trimming, the trimmer head should be in the position
shown in fig. B. If it is not:
◆ Depress the adjustment button (6).
◆ Rotate the tube (7), while releasing the button.
◆ When the head is in position, the button will lock into
place.
Note: The tube will only rotate in one direction.
Edging mode (fig. C & D)
For edging, the trimmer head should be in the position shown
in fig. C. If it is not:
◆ Depress the adjustment button (6).
◆ Rotate the tube (7), while releasing the button.
◆ When the head is in position, the button will lock into place.
Note: The tube will only rotate in one direction.
Adjusting the height of the tool (fig. D)
This tool has a telescopic mechanism, allowing you to set it to
a comfortable height. There are three height settings. To
adjust the height setting, proceed as follows:
◆ Depress the adjustment button (6).
◆ Gently pull the tube (7) out of the motor housing (16) to
the desired height, while releasing the button.
◆ When the tube is in position, the button will lock into
place.
Switching on and off
◆ To switch the tool on, squeeze the trigger lever (1).
◆ To switch the tool off, release the trigger lever.
Warning! Never attempt to lock the trigger lever in the on
position.
Hints for optimum use
General
◆ In order to achieve optimum cutting results, only cut dry
grass.
Trimming
◆ Hold the tool as shown in fig. B.
◆ Gently swing the trimmer from side to side.
◆ When cutting long grass, work in stages from the top.
Take small cuts.
◆ Keep the tool away from hard objects and delicate plants.
◆ If the tool starts running slowly, reduce the load.
Edging
Optimum cutting results are achieved on edges deeper than 50 mm.
◆ Do not use the tool to create edges. To create edges, use
an edging spade.
◆ Guide the tool as shown in fig. C.
◆ To make a closer cut, slightly tilt the tool.
Maintenance
Your tool has been designed to operate over a long period of
time with a minimum of maintenance. Continuous satisfactory
operation depends upon proper tool care and regular cleaning.
Warning! Before performing any maintenance, switch off and
unplug the tool.
◆ Regularly clean the ventilation slots in your tool using a
soft brush or dry cloth.
◆ Regularly clean the cutting line and spool using a soft
brush or dry cloth.
◆ Regularly use a blunt scraper to remove grass and dirt
from the underneath of the guard.
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker GL716 T2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker GL716 T2 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,62 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Black Decker GL716 T2

Black Decker GL716 T2 Quick start guide - English - 12 pages

Black Decker GL716 T2 User Manual - Polish - 12 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info